To achieve a high quality machined finish on the workpiece and to enable use at high speeds, the tool must be finely balanced with the toolholder, for which purpose balancing holes are provided around the cutter body. To achieve the best possible results, the entire machine environment must be taken into account and brought to the highest possible level of stability. The combination of the machine design, guideways, spindle and workholding system as well as the milling tool have a decisive influence on the result.

The number of flutes determines the stepover percentage because it determines the chip spacing. Tool diameter also plays a role. For example, a 0.5-in.-dia. tool with 9 flutes has less chip spacing than a 1-in.-dia. tool with 9 flutes.

2. Understand the power of CAM. It is impossible to program an optimized roughing strategy manually. You need to use a programming software package that will control the cutting strategy. But not just any programming software will work; it needs to be the right software for this application. A program designed only for high-speed side milling will not perform optimized roughing.

“We have seen as little as a 30 per cent in cycle times and a high end of 80 per cent reduction,” said Ball. “In the upper range, the cycle time reduction also takes into account a reduction in rest roughing and semifinishing.”

The holder needs to provide less than 0.0004 in. of runout. A precise holder ensures the accuracy of the process, whereas a less secure holder will cause undesirable levels of vibration at optimized roughing’s high feed rates.

Tooling manufacturer, Horn has introduced a new carbide insert grade, SG66, for turning components from steel that has been case hardened to 58 HRC.

“Niagara Cutter [a division of Seco] has a multiflute family of tools that is used for this type of cutting. They feature a 38-degree helix, large core diameters, and multiple flutes (6, 7, 9). The tools used for optimized roughing typically have some sort of corner protection (radius or chamfer) and are coated to provide both heat and abrasion resistance, typically an AlTiN coating,” said Bell.

“Today’s CAM software can be programmed to create an optimized roughing stage that uses a large DOC and light radial engagement to maximize metal removal rates. It’s a type of milling operation that is very well suited to pocketing and side profiling,” said Jay Ball, product manager for solid-carbide end mills – NAFTA at Seco Tools.

Optimized roughing is not for every part; it’s very component driven. If a part is a complex, 3-D component, optimized roughing is not going to be the most efficient way to get the highest metal removal rate during the roughing stage. When it can be employed, however, it can have a significant effect on cycle times.

Optimized roughing uses a large DOC and light radial engagement to maximize metal removal rates. Photo courtesy of Seco Tools.

Image

Joe Thompson has been covering the Canadian manufacturing sector for more than two decades. He is responsible for the day-to-day editorial direction of the magazine, providing a uniquely Canadian look at the world of metal manufacturing.

4. Use the tooling manufacturer’s recommended cutting parameters. Do not rely on the default cutting speed and feed rate data from programming software suppliers. Cutting tool suppliers develop the recommended cutting parameters after research and through years of experience. Tool makers optimize cutting data for the tool’s design and specifications and for the material group you are working with.

A new, high-feed milling system for productive finishing of non-ferrous metals and plastics has been introduced by Horn Cutting Tools. Designated DTM 1710, the tool system employs inserts with polycrystalline diamond (PCD) cutting edges brazed onto cassettes that can be finely tuned axially to micron precision via adjusting screws on the tool carrier. The PCD substrate is precisely laser-cut to achieve high surface quality during the finishing process. Axial run-out is set by Horn engineers before the tool is delivered. Compared to other tools of this type on the market, the Horn milling system offers a higher number of cutting edges for any given size. The tools are available in the diameters 50mm (z = 10), 63mm (z = 14), 80mm (z = 18), 100mm (z = 24) and 125mm (z = 30), z representing the number of inserts. All variants have an internal coolant supply directly to the cutting edge. To achieve a high quality machined finish on the workpiece and to enable use at high speeds, the tool must be finely balanced with the toolholder, for which purpose balancing holes are provided around the cutter body. To achieve the best possible results, the entire machine environment must be taken into account and brought to the highest possible level of stability. The combination of the machine design, guideways, spindle and workholding system as well as the milling tool have a decisive influence on the result. The aluminium alloy milling body is lightweight, minimising centrifugal force and hence prolonging spindle life. For long-term protection against abrasion from chips, the cutter body is surface treated. The Horn high-performance PCD cutting material is composed of a mixture of different sizes of diamond grains. As the proportion of diamond by volume increases, so do the effective hardness, toughness and cutting edge quality. For the DTM 1710 milling system, Horn offers two different PCD substrates to suit the material to be machined. www.phorn.co.uk

Today’s advanced optimized roughing is only effective if implemented properly. And while similar in nature to other strategies, optimized roughing entails specific best practices that shops must adhere to and common missteps they must avoid to achieve optimum results.

Connect with the manufacturing community and supply-chain across 3 days at the UK’s leading annual industrial event.

The best use of the optimized roughing technique is in situations that can use the full flute length of the tool, such as roughing long, straight walls. Photo courtesy of Seco Tools.

For the optimized roughing operation to be successful, a constant radial DOC must be maintained. This radial DOC also depends on the material being cut. For example, superalloys can have a radial DOC that is 5 to 7 per cent of the tool diameter, while tool steel under 50 HRC can use 7 to 10 per cent of the tool’s diameter as the radial DOC value.

A new, high-feed milling system for productive finishing of non-ferrous metals and plastics has been introduced by Horn Cutting Tools.

During the roughing phase, the vast majority of material is removed from the part, typically leaving only what is required for the finishing phase.

Keep up to date with the latest news, events, and technology for all things metal from our pair of monthly magazines written specifically for Canadian manufacturers!

The aluminium alloy milling body is lightweight, minimising centrifugal force and hence prolonging spindle life. For long-term protection against abrasion from chips, the cutter body is surface treated.

The Horn high-performance PCD cutting material is composed of a mixture of different sizes of diamond grains. As the proportion of diamond by volume increases, so do the effective hardness, toughness and cutting edge quality. For the DTM 1710 milling system, Horn offers two different PCD substrates to suit the material to be machined.

“There might be some additional corner picking that you need to get closer to near net shape before you can move on to finishing, but this strategy takes the bulk of the material out,” said Ball.

Overall cycle time is dependent on the part. If a part is near-net forged, for example, it will not require as much roughing as a solid block will. Another example is a mould cavity: It requires much more time to be spent in the finishing stage rather than the roughing stage because a smooth 3-D finish is required.

Designated DTM 1710, the tool system employs inserts with polycrystalline diamond (PCD) cutting edges brazed onto cassettes that can be finely tuned axially to micron precision via adjusting screws on the tool carrier. The PCD substrate is precisely laser-cut to achieve high surface quality during the finishing process. Axial run-out is set by Horn engineers before the tool is delivered.

Easily access valuable industry resources now with full access to the digital edition of Canadian Fabricating & Welding.

1. Use the right machine. Machines used for optimized roughing need two things: fast spindles and rigidity. The spindles must generate the necessary revolutions per minute for optimized roughing’s feed rates. The rigidity of the machine minimizes vibration and contributes to part quality.

AE-VMS short series endmills designed for stable milling application, ideal for wide range of material like Carbon steel, Alloy steel and Stainless steel to Titanium alloys and Ni alloys.

“Instead of encasing the tool in 180 degrees of engagement, which creates a lot of heat and a lot of pressure, better metal removal rates are achieved with optimized roughing because machinists can take a 2xD DOC and use a 10 to 12 per cent stepover, depending on material. This means you generate less heat and have less radial engagement, which means you can accelerate feed rate and surface footage rate. This is what reduces cycle time,” he added.

Image

Compared to other tools of this type on the market, the Horn milling system offers a higher number of cutting edges for any given size. The tools are available in the diameters 50mm (z = 10), 63mm (z = 14), 80mm (z = 18), 100mm (z = 24) and 125mm (z = 30), z representing the number of inserts. All variants have an internal coolant supply directly to the cutting edge.

Rigid workholding also is important to minimize vibration in the part or, in the worst-case scenario, movement of the workpiece.

As the number of flutes increases, the stepover must decrease to maintain surface finish at faster feed rates. If the stepover is too large, feed rates must be lowered, and more heat is generated with the larger amount of metal removed in each pass. By decreasing the stepover, faster cutting speeds can be achieved. This requires more passes, but the metal removal rates are still higher than at slower speeds because of the increased feed rates.

When it comes to the overall manufacturing process, optimized roughing can typically remove 90 to 95 per cent of the rough stock on a workpiece. This leaves only about 1 to 2 per cent of the tool diameter as finish stock for removal.

“With any solid-carbide application in which you are trying to hold tight tolerances, the holders can make you or break you,” said Ball. “If you try to run these strategies and these processes in a collet that is not rigid or doesn’t contain the runout, you will struggle to achieve the metal removal rate and cycle time reduction this strategy can provide.”

An award-winning writer and graduate of the Sheridan College journalism program, he has published articles worldwide in a variety of industries, including manufacturing, pharmaceutical, medical, infrastructure, and entertainment.

Walter has now launched its new X·treme Evo Plus drill from the DC180 Supreme product family that is now available up to 8XD for the first time.

Ball suggested milling chucks, shrink-fit holders, and high-precision collet chuck systems when using this milling strategy.

The amount of stepover that can be used depends on tool diameter and the number of flutes on the tool. For example, a 6-flute, 0.5-in. end mill cutting 4140 steel can use a 10 to 12 per cent stepover. With a 7-flute tool, the stepover is only 8 per cent. Moving to a 9-flute tool reduces the stepover to roughly 3 per cent.

Easily access valuable industry resources now with full access to the digital edition of Canadian Metalworking.

3. Don’t cut too deep. A cutting depth of 2xD that takes the full length of the cut in one pass is recommended. The shallow radial stepover enables the depth of the cut. A larger stepover would require a shallower depth of cut to achieve the same metal removal rates. However, a cut that is too deep, more than 3xD for example, creates cutting pressures greater than the tool can bear and causes deflection.

If you find this article informative, consider subscribing digitally to Aerospace Manufacturing for free. Keep up to date with the latest industry news in your inbox as well as being the first to receive our magazine in digital form.

ANT Industries, a leading manufacturer of aero engine and gas turbine components in Atherstone, Warwickshire, has announced a significant milestone in its commitment to quality and excellence.

Optimized roughing improves metal removal rates (Q), reduces the amount of time spent in the roughing phase, and increases tool life, all while reducing the load on the machine, according to Ball.

Image

The NeoMill-Alu-QBig indexable insert milling cutter from Mapal stands for top performance in high-volume milling of aluminium. The tool manufacturer thus offers a very economical solution for use on high-performance machines, such as those found primarily in the aerospace industry.

According to Ball, the best use of optimized roughing is in situations that use the full flute length of the tool. Roughing long, straight walls is a good example of this.