The surface quality is also dependent on the coolant, said Doiron, with optimal results produced using minimum quantity lubricant (MQL) oil.

If you're looking at a cutterhead with segmented knives or inserts, carbide is a good choice because at worst you'll shatter the inserts that hit the nails.

Joe Thompson has been covering the Canadian manufacturing sector for more than two decades. He is responsible for the day-to-day editorial direction of the magazine, providing a uniquely Canadian look at the world of metal manufacturing.

Image

Stack Exchange network consists of 183 Q&A communities including Stack Overflow, the largest, most trusted online community for developers to learn, share their knowledge, and build their careers.

The geometry of the tool (see Figure 1) has cutting edges that remove material [shown in red] and pressure ridges that compact and smooth the material to produce polished surfaces [shown in green].

If you're looking at long jointer knives, high-speed steel is a proven material, and if you happen to completely trash your knives by running nails through your machine, the knives aren't very expensive to replace.

An award-winning writer and graduate of the Sheridan College journalism program, he has published articles worldwide in a variety of industries, including manufacturing, pharmaceutical, medical, infrastructure, and entertainment.

Machine shops have many options when searching for a solid-carbide end mill. The type of end mill, geometry, and coatings all are selected based on the operation and the material being cut. Then it’s time to rough, and then finish the cut.

Emuge Corp., West Boylston, Mass., has introduced the Cut & Form solid-carbide finishing end mill, which features a patented tool geometry that performs two functions -- cutting and polishing -- in one operation.

Image

Easily access valuable industry resources now with full access to the digital edition of Canadian Fabricating & Welding.

All else being equal, anytime you have a choice between HSS (high speed steel) and carbide, you have to consider the tradeoffs.

Image

“This medium is 100 per cent free from other microparticles in comparison to standard emulsion coolant. However, coolant can also be used with success if oil application is not desired,” said Doiron.

ISCAR is About to Change Metal Cutting…AGAIN. QUICK-X-FLUTE – NEW Innovative Extended Flute Cutters Optimized for Efficient and Cost-Effective Roughing of High-Temperature Alloys and Steel

The tool’s dual functionality comes from its design, which incorporates three cutting edges to remove material and three burnishing edges to compact the material. This produces polished mirror surfaces as fine as 0.08-μm Ra.

“The unique design of the solid-carbide end mills is not only the polished surface quality, but also the surface quality of the pressure ridges. These pressure ridges are designed to compact and smooth the material,” explained Dan Doiron, Emuge milling products manager.

Keep up to date with the latest news, events, and technology for all things metal from our pair of monthly magazines written specifically for Canadian manufacturers!

“The higher the tensile strength, the more critical it is in the compaction of the material,” said Doiron. “Nonferrous materials have a lower tensile strength that requires less cutting force than that of steel or hardened materials.”

“Cut & Form end mills are another example of innovative technology at work [that has been] designed to dramatically speed machining throughput, eliminating time, secondary operations, and cost,” said Bob Hellinger, president of Emuge Corp.

With the “cutting” edge, the tool creates a machining process that uses very small stock material (0.004 to 0.008 in.) for the pressure ridges to produce a polished surface.

“The development stemmed in part from a customer in the communications industry who was looking to finish the exterior of an aluminum housing and wanted a polished surface that did not require any additional polishing after the milling process,” said Doiron.

Typically, finishing operations, depending on the required finish, take the most time to complete. However, a new product may help reduce some of the fine-finishing time required to achieve a polished surface after cutting.

The other important item to note is the substrate of the tool. It is made from solid carbide, which is very hard, and too much force on the tool can prevent the optimal surface finish from being attained in harder materials.