Haimer’s Cool Flash toolholder system was designed to direct coolant to a tool’s surface with no air gap. Coolant collects in a chamber in the holder then is distributed evenly over the entire circumference of the tool shank. Images courtesy Haimer.

Why the focus on nanostrings? “Nanostrings are fundamental building blocks, the very foundation that can be used to construct more intricate suspended structures. Demonstrating high yield strength in a nanostring translates to showcasing strength in its most elemental form.”

Because through-coolant toolholders eliminate the variances often experienced with external cooling nozzles, the additional cost of such holders, which is sometimes zero, can be easily justified through the reduction of cycle times and improvement of tool life and part quality.

Image

“High-temperature alloys need a lot of coolant volume, but not necessarily a lot of pressure,” Miller said. “The higher volume is required for better heat transfer, because you don’t want these materials to get too hot or they’ll workharden and get more difficult to machine.”

Through-coolant toolholders—the third method of coolant delivery—have one or more internal coolant passages. Coolant runs through the spindle, all the way up to the nose of the holder, where it exits two or more ports located close to the shaft of the tool. The toolholders, which are typically modified standards, come with a range of port styles, from simple holes bored with an EDM to elaborate angled passageways running through the chuck.

The Mega Perfect Grip holder from BIG KAISER is designed for applications involving superalloys. It incorporates a key grip that locks the Weldon flat of a cutting tool into place. Three slots in the bore where the key can slide down provide holes for the higher volume of coolant needed to machine such materials. Image courtesy BIG KAISER.

Researchers at Delft University of Technology, led by assistant professor Richard Norte, have unveiled a remarkable new material with the potential to impact the world of material science: amorphous silicon carbide (a-SiC).

Advanced Industries makes two types of KoolBlast through-coolant toolholders: one series with a standard Weldon setscrew and a series of Thermalfit holders. Both use the same unique internal coolant distribution design, according to Beckington.

According to Chelsea, Mich.-based Advanced Industries Inc.’s Chris Beckington, whose company makes KoolBlast toolholders, coolant is especially important when machining with carbide tools. “The thermal stress of heat caused by friction in the cutting zone can wear out the carbide,” he said. “This alternate heating and cooling causes weakness in the tool, so we try to [constantly] keep … coolant on the tool to eliminate the effects of thermal shock.”

“To better understand the crucial characteristic of “amorphous,” think of most materials as being made up of atoms arranged in a regular pattern, like an intricately built LEGO tower,” explains Norte. “These are termed as “crystalline” materials, like for example, a diamond. It has carbon atoms perfectly aligned, contributing to its famed hardness.” However, amorphous materials are akin to a randomly piled set of Legos, where atoms lack consistent arrangement. But contrary to expectations, this randomization doesn’t result in fragility. In fact, amorphous silicon carbide is a testament to the strength emerging from such randomness.

Choosing a through-coolant toolholder depends a lot on the application. For example, BIG KAISER’s Mega Perfect Grip toolholder was designed specifically for milling heat-resistant superalloys.

When drilling, a force that is directed axially—along the direction of machining. The magnitude of an axial force rises with the drill’s diameter and the chisel edge’s width. Axial force is also known as thrust. When turning and boring, the term “feed force” is commonly used instead of “axial force.” See cutting force.

The researchers adopted an innovative method to test this material’s tensile strength. Instead of traditional methods that might introduce inaccuracies from the way the material is anchored, they turned to microchip technology. By growing the films of amorphous silicon carbide on a silicon substrate and suspending them, they leveraged the geometry of the nanostrings to induce high tensile forces. By fabricating many such structures with increasing tensile forces, they meticulously observed the point of breakage. This microchip-based approach not only ensures unprecedented precision but also paves the way for future material testing.

Whatever the material, through-coolant toolholders provide numerous benefits. “You get increased tool life because you’re keeping the cutter cool, so you can cut faster and get better surface finishes,” said Advanced Industries’ Beckington.

Looks like a couple folks in the comments here think they are real smart. But nitpicking the author of an article meant to simply spread news of a breakthrough kinda feels silly. Save the woodpeckering for the study written by the researchers. Anyway looks like some cool stuff on the horizon.

Haimer offers Cool Jet and Cool Flash systems for its shrink-fit chucks. Cool Jet, which comes standard with nearly all Haimer shrink-fit holders, features angled internal bores in the walls of the holder that facilitate coolant exiting the nose of the chuck. Cool Flash is an upgradable option that has a series of T-slots around the ID of the chuck to apply coolant directly to the shank of a cutting tool. This option is particularly beneficial at higher speeds, where greater pressure is inherently needed.

And what finally sets this material apart is its scalability. Graphene, a single layer of carbon atoms, is known for its impressive strength but is challenging to produce in large quantities. Diamonds, though immensely strong, are either rare in nature or costly to synthesize. Amorphous silicon carbide, on the other hand, can be produced at wafer scales, offering large sheets of this incredibly robust material.

“In the majority of cases for endmills, the coolant’s either being fed externally with nozzles or it’s coming through the toolholder,” he said.

Maintaining accurate balance is the reason that Haimer designed its Cool Flash system with a permanent, laser-welded cap on the chuck, Strauchen said. “This way there’s no moving parts, and no fear of throwing the balance out of specification.”

The range of potential applications is vast. From ultra-sensitive microchip sensors and advanced solar cells to pioneering space exploration and DNA sequencing technologies. The advantages of this material’s strength combined with its scalability make it exceptionally promising.

1. Spreading of a constituent in a gas, liquid or solid, tending to make the composition of all parts uniform. 2. Spontaneous movement of atoms or molecules to new sites within a material.

Substances having metallic properties and being composed of two or more chemical elements of which at least one is a metal.

These “breakthroughs” have been reported for decades, yet rarely do they come to fruition. Hopefully it will pan out, someday.

Pioneer N.A. does things a little differently. It will EDM through-coolant holes into any of the toolholders it inventories.

One method is Coolant Ring Technology toolholders from Scientific Cutting Tools Inc., Simi Valley, Calif., which reportedly enhance coolant penetration, such as into a bore. In that scenario with a conventional through-coolant holder, coolant hits the face of the part and splashes back. The CRT holder, on the other hand, delivers coolant all the way around a tool instead of one quadrant of the tool, so wherever there is space to get into the bore, coolant is there. The result, said Scientific, is a 75 percent higher level of coolant penetration.

Toolholder companies have developed a number of creative ways to try to overcome the vortex effect and ensure that coolant meets its mark at higher speeds. The standard design uses round holes situated about 1mm (0.039") from the tool shank, requiring the coolant spray to “travel” a bit before it touches the shank.

“With amorphous silicon carbide’s emergence, we’re poised at the threshold of microchip research brimming with technological possibilities,” concludes Norte.

A new material that doesn’t just rival the strength of diamonds and graphene, but boasts a yield strength 10 times greater than Kevlar, renowned for its use in bulletproof vests.

“For some through-coolant systems with add-on parts, like sleeves that fit over a toolholder, you run the risk of putting the assembly out of balance,” Strauchen said, “and the faster it rotates, the more that imbalance will cause vibration in the spindle, which can lead to chatter, degraded tool life and less productivity.”

Secures a cutting tool during a machining operation. Basic types include block, cartridge, chuck, collet, fixed, modular, quick-change and rotating.

Similarly, Haimer designed its circular Cool Jet bores to run at 3° angles so that as coolant exits the toolholder, it is aimed directly at the cutting edge. “But even so, when you rotate fast enough, the separation still makes it easier to atomize,” Strauchen said.

Electric heating positive and positive sep volt Levi heat separation pressure and vacuum atomic structure interweave interlinking recovery adjustment and brake the change to be a world changing project

BIG KAISER Precision Tooling Inc., Hoffman Estates, Ill., offers a line of through-coolant hydraulic chucks with two small holes on the face of the chuck angled to direct coolant down the endmill shank.

Flick noted that a lot of older machines have 50-psi coolant pumps while many newer machines are equipped with 1,000-psi systems. “Most of these higher-pressure machines can run at 20,000 rpm because they have enough coolant pressure, while the older machines are probably running 3,000 or 4,000 rpm.”

Holly B. Martin is a science writer and technical copywriter based in Winchester, Va. For more information, visit www.hollybmartin.com.

By effectively delivering coolant to the cutting tip, SCT stated that the tip will only be a couple of degrees warmer than the coolant temperature. But if there is not an ample supply of coolant to the tip, the tool can get hot enough to negatively impact the carbide binder and deformation of the carbide can occur. Also, heat can cause a part to thermally expand and make it difficult to hold a tight tolerance.

Process that vaporizes conductive materials by controlled application of pulsed electrical current that flows between a workpiece and electrode (tool) in a dielectric fluid. Permits machining shapes to tight accuracies without the internal stresses conventional machining often generates. Useful in diemaking.

Milling cutter held by its shank that cuts on its periphery and, if so configured, on its free end. Takes a variety of shapes (single- and double-end, roughing, ballnose and cup-end) and sizes (stub, medium, long and extra-long). Also comes with differing numbers of flutes.

Thin web or film of metal on a casting that occurs at die partings and around air vents and movable cores. This excess metal is due to necessary working and operating clearances in a die. Flash also is the excess material squeezed out of the cavity as a compression mold closes or as pressure is applied to the cavity.

The KoolBlast Thermalfit through-coolant toolholder from Advanced Industries features D-shaped orifices and the company’s PressureMax design, which together minimize turbulence as coolant contacts the cutting tool. Image courtesy Advanced Industries.

A second method of applying coolant is to run it through the tool itself. This is the most accurate way to direct coolant to the cutting zone, but tools with through-coolant capability are mostly limited to drills, Strauchen said.

Applying coolant while machining is important for two related reasons: It keeps the cutting tool edge cool and clears chips from the cutting zone.

Image

Flick said the amount of coolant pressure available will dictate how fast a tool can run and yield effective results, based on how fast the coolant evacuates chips. “If you have enough pressure to support it, the more holes you have, the faster you’re going to be able to cut, and the longer your cutting tools are going to last,” he said.

Similarly, flood coolant systems incorporating flexible plastic nozzles often aren’t positioned properly, “because the operator assumed positioning does not matter,” Strauchen said, “or, more likely, something happened during a machining process or a tool change where the nozzles got bumped and are no longer directing coolant anywhere near where they’re supposed to.”

To counteract these strong forces, the Mega Perfect incorporates a key grip that locks the Weldon flat of a cutting tool into place. In addition, the three slots in the bore where the key can slide down provide holes for the higher volume of coolant delivery needed for these types of applications.

Scientific Cutting Tools’ Coolant Ring Technology toolholder provides a 360° coolant delivery pattern. Image courtesy Scientific Cutting Tools.

BIG KAISER also offers through-coolant features on several different series of collet chucks. “That gives you the versatility of a collet chuck program—to grab any tool size—whereas hydraulic chucks are more or less dedicated to one specific size,” Miller said.

“You can also control your chip evacuation better, compared to flood coolant,” he added, and the coolant is “more centralized to the cutting area, so you’re evacuating chips in pockets and cavities and not recutting them. It helps you keep a nice clean workspace where you’re cutting.”

Designing an effective through-coolant toolholder requires an understanding of the “vortex effect.” As the tool rotates at higher and higher speeds, it whips up a vortex of air, which creates a barrier that can prevent coolant from reaching the tool/workpiece interface.

Pioneer through-coolant toolholders come with two orifices standard. The company will EDM additional holes for a charge. Image courtesy Pioneer.

KoolBlast developed a unique D-shaped orifice design for its new Thermalfit through-coolant toolholders, along with patented internal passageways that pressurize the coolant before releasing it. “With our new design, coolant exits at a specific angle and location so that it hits the tool in a way that maximizes the velocity while fighting through the turbulence from the centrifugal force that prevents it from reaching the cutter,” Beckington said.

“If your area for delivering coolant is reduced, the laws of physics dictate that the force at which the liquid leaves the holder will be greater,” said Haimer’s Strauchen. “So somebody who has limited coolant pressure of only about 150 to 300 psi can maintain proper cooling without diffusion at high speeds (up to 18,000 rpm), where they would otherwise need 600 to 750 psi to maintain proper cooling.”

Diamonds are relatively rare. When was the last time you saw one in the rough on the ground? Ever? Just because something is rare doesn’t mean that it can’t be obtained in quantities sufficient for commercial applications.

Flexible-sided device that secures a tool or workpiece. Similar in function to a chuck, but can accommodate only a narrow size range. Typically provides greater gripping force and precision than a chuck. See chuck.

This led the company to upgrade its design to one that would deliver the coolant directly to the tool shank with no air gap. “What makes our Cool Flash system unique is that the coolant exits through small perpendicular slits located around the internal diameter of the toolholder,” Strauchen explained. “This not only helps coolant reach the shank, because it’s being directed straight onto it, but by taking advantage of surface tension and centrifugal forces, the coolant is actually being spun up the shank of the tool. So, centrifugal forces are working for us instead of against us.”

Condition of vibration involving the machine, workpiece and cutting tool. Once this condition arises, it is often self-sustaining until the problem is corrected. Chatter can be identified when lines or grooves appear at regular intervals in the workpiece. These lines or grooves are caused by the teeth of the cutter as they vibrate in and out of the workpiece and their spacing depends on the frequency of vibration.

Fluid that reduces temperature buildup at the tool/workpiece interface during machining. Normally takes the form of a liquid such as soluble or chemical mixtures (semisynthetic, synthetic) but can be pressurized air or other gas. Because of water’s ability to absorb great quantities of heat, it is widely used as a coolant and vehicle for various cutting compounds, with the water-to-compound ratio varying with the machining task. See cutting fluid; semisynthetic cutting fluid; soluble-oil cutting fluid; synthetic cutting fluid.

Reference: “High-Strength Amorphous Silicon Carbide for Nanomechanics” by Minxing Xu, Dongil Shin, Paolo M. Sberna, Roald van der Kolk, Andrea Cupertino, Miguel A. Bessa and Richard A. Norte, 12 October 2023, Advanced Materials. DOI: 10.1002/adma.202306513

Machining operation in which metal or other material is removed by applying power to a rotating cutter. In vertical milling, the cutting tool is mounted vertically on the spindle. In horizontal milling, the cutting tool is mounted horizontally, either directly on the spindle or on an arbor. Horizontal milling is further broken down into conventional milling, where the cutter rotates opposite the direction of feed, or “up” into the workpiece; and climb milling, where the cutter rotates in the direction of feed, or “down” into the workpiece. Milling operations include plane or surface milling, endmilling, facemilling, angle milling, form milling and profiling.

Beyond its exceptional strength, this material demonstrates mechanical properties crucial for vibration isolation on a microchip. Amorphous silicon carbide is therefore particularly suitable for making ultra-sensitive microchip sensors.

It’s rare to see through-coolant in a hydraulic chuck because it has a lot of internal features, making it difficult to get coolant around them and out, said Alan Miller, engineering manager at BIG KAISER. “We really only recommend hydraulic chucks for finishing endmills—it’s typically going to be a ballnose endmill, probably in a 5-axis environment, to really get the benefit.”

“Any time there is an unplanned stoppage due to tool breakage or additional rework added to a job to fix bad parts, a huge cost is incurred,” Strauchen said. “We try to convey to people that a through-coolant toolholder is a  capital expenditure and should be implemented as a best practice. You’re going to benefit for the next several years from it.”

According to Drew Strauchen, vice president of marketing and business development for Haimer USA LLC, Villa Park, Ill., machinists often run down five or six rabbit holes and spend a lot of time and money investigating the cause of the problem before they think, “ ‘Wait—how are we delivering coolant here?’ ”

Workholding device that affixes to a mill, lathe or drill-press spindle. It holds a tool or workpiece by one end, allowing it to be rotated. May also be fitted to the machine table to hold a workpiece. Two or more adjustable jaws actually hold the tool or part. May be actuated manually, pneumatically, hydraulically or electrically. See collet.

For Pioneer toolholders, the company offers customers the option of having their tool assemblies rebalanced once the coolant holes have been drilled. “We recommend they send us their cutter, and we’ll put the tool into the toolholder, put it on the balancing machine and trim up the whole assembly based on how fast they intend to run it, whether it’s 5,000 rpm or 20,000 rpm,” Pioneer’s Flick said.

Flick said a lot of customers initially are skeptical that adding through-coolant capability to a toolholder will do much good. “They just don’t get it,” he said. “So when we go into their shop and actually run it for them, they’re blown away at the difference it makes—and for a very small upcharge.”

There are three basic ways to apply coolant during machining. The most common way is with external nozzles—a process called flood cooling. However, problems often occur with this type of system. For example, copper flood coolant lines are fixed to the machining head so they don’t move. But when machining parts with features such as a shoulder or a ledge, the tool can dip down below that ledge to work at the bottom of a surface, blocking coolant from reaching the cutting zone.

Isaac Azimov stuff. I’m an inventor and US Patent holder. My juices are working on products that create industries and cultural changes. Soon, will have a 501c3 corporation that’ll turn the world on its ears. Thanks for the impetus to thoughts’ !

Imagine that this nightmare machining scenario has just hit: Your tool life suddenly shrinks from 100 parts to 10 parts, the surface finish of your workpiece rapidly degenerates and—worst of all—an endmill breaks in the toolholder.

Similar to placing your thumb over the end of a garden hose, the design of a through-coolant toolholder can help increase the pressure of the coolant hitting the cutting surface.

“We put in two holes standard, but we charge $20 per additional hole, so if a customer has enough coolant volume coming through the machine to support it, we can put in more,” said Lee Flick of Pioneer, Elk Grove Village, Ill. “We’ve done as many as 12 holes in a holder for one of our customers.”

The tensile strength of this new material is 10 GigaPascal (GPa). “To grasp what this means, imagine trying to stretch a piece of duct tape until it breaks. Now if you’d want to simulate the tensile stress equivalent to 10 GPa, you’d need to hang about ten medium-sized cars end-to-end off that strip before it breaks,” says Norte.

In some cases, coolant may not even be desirable. “When you get into steels, a lot of times you’ll be doing more roughing work, and the coating technologies of these tools work better without coolant, though people will still use air to get chips out of the way,” Miller said.

“There’s so much axial force when the cutting tool engages with these materials, it tries to physically pull the cutting tool out,” Miller said, “and the forces can get so high that even with very strong clamping forces, they can slip.”

Article about tensile strength but intro reads like the article conflates hardness of diamond and toughness of kevlar as strength.

Main body of a tool; the portion of a drill or similar end-held tool that fits into a collet, chuck or similar mounting device.

Image