tungsten carbide, an important member of the class of inorganic compounds of carbon, used alone or with 6 to 20 percent of other metals to impart hardness to cast iron, cutting edges of saws and drills, and penetrating cores of armour-piercing projectiles.

Image

These five types of big bits look very different from each other, and perform differently as a result. This chart gives you their basic capabilities at a glance, but be sure to read the full write-ups that follow for all the important details. Price ranges are for individual bits.

Contrary to popular wisdom, Forstner bits can be used with handheld drills, but be sure to go in straight and square and start with a light touch. Forstner bits can bore deep holes, but you’ll need to withdraw the bit frequently to clear chips and help prevent overheating. The same geometry that cuts clean-sided holes puts a lot of steel in contact with wood, producing extra friction. If your bits will be subjected to heavy use, consider spending the extra money for carbide Forstners that can take the heat without getting dull.

Stopped holes, sort of. A spade bit can drill a stopped hole, but the long center spur leaves a deep, narrow hole in the middle.

A holesaw won’t cut as cleanly as a circle cutter, but it can make holes just as big. You can use these bits in a handheld drill, but make it a powerful one. These hefty bits demand high torque and a firm grip. In my tests, I found that holesaws with fewer teeth—and long slots ahead of those teeth to eject chips—cut worlds better than those with continuous teeth around the rim. Like circle-cutters, holesaws can only drill through holes, in materials up to about 2" thick. If you don’t own a drill press, or you are facing a remodeling job that requires big holes in construction lumber, a holesaw is right for you. Holesaws equipped with “bi-metal” or carbide teeth can also drill through thin metal.

To solve the big bit puzzle, I ordered a bunch of plus-sized bits and collected plenty of wood to use for various drilling assignments. You’ll find plenty of helpful information in the chart on the facing page, and in the write-ups that follow. With these details, you’ll be able to match the bit to the job and get the best value from every bit of money you spend on these tools.

Image

With a lead screw that keeps them on track and pulls them through the wood, plus deep flutes for ejecting chips efficiently, auger bits drill deep, smooth holes, even if you enter the wood at an angle. The lead screw forces a feed rate that works well in softwoods, letting contractors bore big holes through a stack of studs at once, for plumbing and electrical components. But that aggressive feed rate can be a problem in hardwoods, causing auger bits to jam in a drill press or cordless drill. Put them in a hand-powered brace, however, and they are a chairmaking champion, boring round mortises in square or round legs, at any angle.

Image

Tungsten carbide is a dense, metallike substance, light gray with a bluish tinge, that decomposes, rather than melts, at 2,600° C (4,700° F). It is prepared by heating powdered tungsten with carbon black in the presence of hydrogen at 1,400°–1,600° C (2,550°–2,900° F). For fabrication, a process developed in the 1920s is employed: the powdered tungsten carbide is mixed with another powdered metal, usually cobalt, and pressed into the desired shape, then heated to temperatures of 1,400°–1,600° C; the other metal, which melts, wets and partially dissolves the grains of tungsten carbide, thus acting as a binder or cement. The cemented composites of tungsten carbide–cobalt are known by many trade names, including Widia and Carboloy.

Anatomical details vary greatly when you move from one big bit type to another. So it’s not surprising that there are differences in cost and performance. By considering the following factors, you can make sure that you get the results you’re after, and that you’re not using an expensive bit to do work that a more affordable bit can tackle effectively.

In any workshop or homeowner’s toolbox, you’re sure to find a good selection of small bits—a set of standard twist drills and, if you’re lucky, a full set of brad-point bits also. But that bit kit tends to peter out when you get to larger diameters, let’s say ¾" or greater. There are plenty of tasks that require big bits (sidebar, right), but it’s not always easy to choose the bit you need, because of the bewildering array of types available.

For many reasons, I consider a set of Forstner bits to be a must-have in any woodworking shop. Although there are slight differences in Forstner bits made by different manufacturers, the basic cutting geometry features a precisely machined rim, a center spur, and a chipper. These cutting elements work together to produce tearout-free, flat-bottomed holes in any type of wood. What’s more, Forstner bits can bore straight, angled, or overlapping holes. You can even bore a partial hole on the edge of a board, as shown in the photo at left. Count on these bits for perfect counterbores, smooth dog holes, decorative cutouts, and round recesses of all kinds—and for clearing the waste out of mortises without wandering.

A contractor’s favorite, spade bits offer the least expensive path to moderately large holes, and they work in handheld drills and drill presses alike. Although they’re designed to bore quickly through soft construction lumber, they drilled surprisingly clean holes in hardwoods in my tests. But the paddle-shaped design makes spade bits prone to vibration and rough cuts when they get dull, which they do relatively quickly. Also, while they can drill flat-bottomed holes, the long center tip leaves a deep, narrow hole on the middle. For all these reasons, buy spade bits in a pinch, but get a set of Forstners when you can afford them.

I tested a variety of Forstner bits; some had wavy teeth around the rim, while others had straight teeth or simply a sharp bevel. The performance differences I noticed were slight, with mid-priced Forstners performing as well as more expensive versions. To get the most for your money, buy a set of Forstner bits instead of acquiring them individually.

You’ll need a drill press to use this tool safely, but for holes larger than a Forstner can manage, you can’t beat a circle cutter. Infinitely adjustable for diameters up to 6", this big-hole specialist replaces a pile of expensive holesaws, for example, and cuts cleaner, smoother holes in the bargain. Use it to cut snug-fitting openings for vac hoses in shopmade jigs, fences, etc. As a bonus, you can invert the cutter to create toy wheels and other perfect disks. The cutter is also very easy to sharpen. To use a circle cutter safely, choose a low speed on your drill press, clamp down the work, keep your fingers clear, and feed the tool slow and steady. You’ll be amazed at the results.