Rotary paper cutters are sometimes designed with transparent cutting surfaces. This feature can improve visibility when cutting and prevent mishaps. Rotary paper cutters have a smaller blade than guillotine paper cutters, but the blade is still very sharp. The blade on some rotary paper cutters won’t work unless the housing is pressed down, which offers an additional measure of safety.

Stack paper cutters have the potential to be very dangerous. Their sharp blades are designed to cut through a large stack of papers and could easily cause harm to children or adults. When not in use, stack paper cutters often lock in place and are relatively safe. The danger comes during use, and the operator should treat the cutter as a power tool—it should not be used when small children are present, and older children should only use it with adult supervision.

Rotary paper cutters are sometimes referred to as paper trimmers. These models feature a sliding blade that can simultaneously cut through a few sheets of paper. The cutting mat on a rotary paper cutter includes a grid design to help users accurately line up each sheet of paper for a precise cut. The grids on some rotary paper cutters also have guidelines extending from the blade at various angles to help make more intricate cuts.

Those looking for a multiple-sheet rotary paper cutter should consider this option by Carl Manufacturing. It comes with a handy locking bar that raises to slide papers under the guide and then locks them in place during the cutting process. We found this especially helpful when cutting thicker stacks of paper sheets.

The following paper cutters all scored well in our hands-on testing. While each offers a range of functions best suited to specific types of projects, all are among the best options for quality paper cutters. We cover the pros and cons of each model so our readers can make an informed buying decision.

Use: Concrete block, mortar, brick | Type: Rotary (non hammer) carbide-tip twist drill | Number of bits: 14 | Size range: ⅛ to ½ inch

This model provides a safety latch to keep the guillotine arm secure when it isn’t in use. It also offers an additional safety guard rail adjacent to the blade to protect fingers during use. The solid wood base is sturdy and comes with rubber bumpers that kept the paper cutter from sliding on the table as we tested it. At 18 inches long by 18 inches wide, it is also generously sized for larger cutting projects.

The blade on a rotary paper cutter is underneath the sliding housing. Some blades are slightly exposed at the edges, while the blade’s housing entirely protects others. Those looking for a safe cutter that children can use for crafting projects will want to choose one where the housing completely encompasses the blade to reduce the risk of injury.

The overall dimensions of the cutting bed are 18 inches long by 12 inches wide. A perforated blade, a straight blade, and a storage compartment to hold extra blades are included. After replacing the existing blade with the perforated blade, we were able to create tear-off sections on papers.

Okay, by now you might be saying to yourself, “All I want is a basic set of bits for wood and metal. Got any of those?” Yes. For less than $20 you get a high-quality hex shank bit with a highly wear-resistant titanium nitride coating. And if you up your game some day to include working with an impact driver, these bits will work with it.

The only sure way to make consistent and clean holes in glass and ceramic tile is with a carbide bit designed for those materials. These simple and inexpensive little bits work great. The carbide tip is diamond ground to a sharp point that enables a fast and sure start, putting the hole right where you need it, instead of the bit skating off and leaving a nasty mark. The three flats ground onto the bit’s shank prevent it from slipping.

Unlike the other cutters we tested, the HFS has a bit of a learning curve, but once we understood how it operated, we found it straightforward to use. The HFS features knobs, buttons, clamps, and handles, all of which adjust to hold various-size stacks of paper firmly when cutting.

To cut a straight line with a paper cutter, using the grid lines on the cutting bed to align the paper is essential. Once the paper is correctly aligned, either pull down the arm or slide the trimmer blade to cut, depending on the type of paper cutter.

The cutting bed measures 21 inches long by 15 inches wide and comes with metric and ANSI markings, making it versatile for most users. The large steel handle is removable for storage, and the cutter features an on-deck tool holder for stowing the small wrenches (included) needed to assemble the cutter.

Those considering a stack or guillotine paper cutter should pay close attention to arm design. The arm on paper cutters pulls down to slice through the paper; however, quality products are distinguished by a tension mechanism that prevents the arm from coming down accidentally on its own. This is an important safety feature because if the arm comes down while the user is still positioning the paper, the blade could cut in the wrong spot or, even worse, injure the user.

Use: Wood and steel | Type: Extra-long twist drill | Number of bits: 5 | Size range: ¼ to ½ inchSuppose you need more reach when making a hole, such as when you’re working on an old house or restoring an old car. Or in a modern house, you need a super-long pilot hole for that massive screw you’ll use to hang a ceiling fan. Enter these 18-inch bits. Built from high-speed steel and with geometry to eject metal chips, they work on wood, too (though you will have to back them out repeatedly as you go deeper to eject the wood chips).

How To Select a SetThere’s no sense in getting bogged down in complexities of hole making–the fine points belong to industrial users. For the rest of us, all we really need to know are the basics. That’s why we separate out bits for making holes in wood, metal, masonry (concrete or stone), and tile/glass. Some of the drill bits do a pretty good job making holes in more than one material. Other than selecting a bit based on the material you’re drilling, keep in mind the quality of the hole you’re making. That sounds odd. A hole is a hole, right? Wrong, There’s a big difference between a perfectly round and smooth-walled hole for furniture making than a rough-and-ready hole made in framing lumber to fit a pipe or cable. So think about the material, the hole itself, and how you want to make it. Choose your set accordingly.

Guillotine paper cutters are a popular choice for schools, offices, and individuals who need to cut larger quantities of paper quickly. The design features a long arm attached to a cutting blade that the user pulls down to slice through a single sheet or stack of paper. To prevent injuries or premature cutting, the blade is often designed with a tension spring that keeps it in place until it is pulled down.

This guide will explore the different types and cover the considerations to keep in mind while shopping. Ahead, learn more about our testing process and find out how the following models earned a spot in our lineup of the best paper cuttersfor most users.

We liked the rubber feet on the bottom of the cutter, which kept it from sliding around during use, but overall, it didn’t score high enough to be among our top picks. We respect the Fiskars brand and look forward to testing an upgraded and improved model of this lightweight and versatile paper cutter.

The manufacturer claims it will cut up to 20 sheets of paper at a time, and our testing verified that it could—with clean, straight cuts. Unlike some other rotary paper cutters where the user must apply downward pressure on the blade housing to engage the blade, all we had to do was slide the housing from one end of the cutter to the other to cut through the paper.

Stack paper cutters are a subset of guillotine paper cutters; they have a long arm with a cutting blade that the user pulls down to slice through a stack of paper. The primary difference, however, is stack paper cutters have one or more heavy-duty clamps to hold the stack in place and a sharper blade to cut through hundreds of sheets of paper with one pass. We were able to slice cleanly through a paperback book with the stack cutter we tested. The downside is that the thicker the stack, the more physical strength the user needs to pull the blade arm down.

Spade bits are made for quick-and-rough holes in construction lumber. They don’t leave a particularly clean exit hole, but in most cases that doesn’t matter. Of all the spade bits we’ve tried through the years, we keep coming back to Irwin Speedbor. They’re inexpensive, tough, and can be sharpened with a file. One set will last for years, maybe decades, depending on your use.

A plus for the 534 is the inclusion of a bar magnet that helps hold a sheet of paper in place while cutting, and even though the guillotine blade does not come with a safety latch, it takes a firm pull to raise the blade, which we felt a toddler probably could not do. Plus, it has a plastic guard next to the blade, which keeps fingers from sliding under it. This is an excellent paper cutter, but this is not the best option if shoppers are looking for U.S.-standard guidelines.

It’s often said that you don’t need a drill bit; what you need is a hole. How you make that hole is up to you, but it’s a given that you want to make it as efficiently as possible. The drill bit, therefore, is built to match the diameter and length of the hole you want to make—as well as the material in which it works. And chances are good that you need more than one bit, you probably need at least a small set to make holes of various diameters.

While the manufacturer claims the cutter can handle up to 12 sheets of paper, we found that it cuts best with eight or fewer sheets. At more than eight, the blade pulls the sheets slightly and leaves ragged edges. Still, this is a nice little cutter for light-duty projects and will fit in most tote bags for easy carrying. It’s a simple, no-frills paper cutter that we feel is well suited for small craft or household projects.

Rotary paper cutters have a sliding blade. This blade type is often used for precise cutting needs, such as trimming photos for scrapbooking. Sliding blades don’t cut as well through multiple sheets of paper at once.

We found it to be well designed and accurate. We’d ask for a more secure safety latch if we had our druthers. With a bit of maneuvering, little fingers might be able to push the latch to the open position, which would allow full access to the blade. Plus, the bottom of the blade extends about 0.0625 inch below the cutting bed when closed and locked in place, so never position hands on the side with the blade when lifting the paper cutter.

The guillotine paper cutter from X-Acto is ideal for cutting through various sheet materials, including paper, photographs, film, and poster board. This is the type of paper cutter we remembered from our school days, and it was every bit as precise at cutting a stack of 15 sheets of paper as it was when we cut a single sheet. We liked that it has horizontal and vertical grid markings in addition to two rulers—one near the top and another near the bottom of the cutting bed. The lines and markings made it easy to select the correct size when cutting and aligning the paper.

The cutting bed measures 22 inches long by 11 inches wide, and the base has rubber feet that keep it from sliding during test cuts. The manufacturer claims the 534 can cut up to 15 sheets of paper, but we found it topped out at 13 sheets. Every time we added one more sheet, the cutter pulled on the stack of 14, and the cut edges were slightly uneven.

In addition to the four types of paper cutters described above, it’s essential to consider various features before selecting the best paper cutter for particular tasks and projects. Paper cutters are available in different sizes, offer other cutting mechanisms, and include various safety features. Shoppers will want to think about these features and decide what suits their needs best.

The biggest downside of a rotary cutter is that most can’t cut through as much paper at a time as a stack or a guillotine model. Some rotary paper cutters may be able to cut through up to 10 sheets at once but are most accurate when cutting only one or two sheets at a time.

The guillotine arm features a spring that keeps the arm from falling when it’s raised, which adds a measure of safety, but we wouldn’t recommend this paper cutter for classes or homes with small children. A small wire latch slips over the handle to keep it from being lifted, but it doesn’t offer much protection as it’s simple to move out of the way. Another downside: The Swingline cutter doesn’t have rubber feet; consider using it on a nonslip surface, such as a rubber pad, to keep it in place.

Shoppers will want to consider two main points when deciding on the best size of paper cutter for them. First, they’ll want to determine how they plan to use the paper cutter, such as the types and sizes of materials they’ll be cutting. Second, they may want to determine how much space they have to store and use the paper cutter.

Electric paper cutters are the most advanced—and the priciest—option to consider. These models feature an automatic motor that powers the paper cutter to slice through a stack of paper. The capacity of each electric paper cutter varies, but some options can cut over 500 sheets of paper at once.

We’ve long been fans of Fiskars scissors and rotary hand cutters, but the Fiskars SureCut Deluxe Paper Trimmer didn’t live up to our high standards. While we liked the guidelines on the cutting mat for making stock photo and business-card-size cuts, the cutting blade wasn’t sharp enough to make crisp, clean cuts on more than two pieces of stacked paper—we ended up with ragged edges. We also discovered the fold-out ruler, which is supposed to extend the cutting width measurement up to 15 inches, was challenging to extend fully. It was supposed to snap into place via a small plastic guide on the underside of the cutter, but when we tried to snap it into place, the plastic guide broke off.

Before we selected several paper cutters for hands-on testing, we researched more than 30 models to determine which ones were most likely to stand up to the cutting tasks of our readers. We looked at ratings and reviews, but we also carefully analyzed cost, weight, design, and safety features, keeping in mind that users’ projects vary widely.

If you’re gearing up for your first big wiring or pipe job, or if you’re a seasoned pro looking for faster and cleaner hole-making ability, then self-feed bits are the way to go. The lead screw pulls the bit through the lumber while an interior plane shaves the wood as the bit turns. The result is a fast hole and a clean one. For the sake of longevity, the plane blade is sharpenable and the kit includes two removable, replaceable feed screws, because you’re bound to hit fasteners and chew through knots.

The blade on a stack paper cutter is generally located on the far side of the clamp to position the user farther away from it. Stack paper cutters are usually designed with a guard to keep the exposed side of the blade covered.

A sturdy metal base helps keep the paper cutter from sliding around and likely adds to its durability and longevity. The work surface measures a large 28 inches long by 12 inches wide, which is suitable for various cutting projects.

The Dahle 534 trimmer looks like many other guillotine paper cutters at first glance, but as we inspected it more carefully, we noticed a series of angled guidelines on the cutting mat that allowed us to trim paper and card stock at precise 15-, 30-, 45-, 60-, and 70-degree angles. The 534 also offers guidelines for other square and rectangular sizes, but there we found it slightly lacking.

We used a rubric and awarded points based on the quality of the materials, usefulness, design, and functionality. The better a cutter performed, the more points it earned. After testing, we added and averaged the points and used the results to help determine the best uses and categories for the cutters.

Glenda Taylor is a product tester and writer specializing in the construction, remodeling, and real estate industries. She and her husband own a general contracting company, and Taylor is experienced in both residential and commercial building applications. She tests a wide range of power tools as well as other home improvement, household, and lawn-and-garden products.

Stack and guillotine paper cutters feature an extendable arm with a blade that pulls down to cut through paper. Users will often have to put more pressure on the blade to slice through a larger stack of paper.

Paper cutters are available in a wide variety of sizes, ranging from compact options, which are only a few inches wide and about as long as a standard sheet of paper, to larger models designed to cut full sheets of construction paper or poster board.

We tested it on single sheets of paper and then on a stack of 10 sheets. It made clean-cut edges on both, although we had to hold the stacked sheets firmly to keep them from shifting when we cut. The rotary feature makes this paper cutter safer than a guillotine cutter—a better option for homes with young children.

The manufacturer claims the HFS will cut up to 400 sheets—or a 1.5-inch stack of paper. We didn’t count the sheets in our stack, but we did measure a 1.5-inch stack for testing. It took half a dozen tries to cut the stack—the thickness made it physically challenging to lower the handle that controls the blade. Eventually, we discovered that lowering the handle as quickly as we could—almost jerking it—let us slice through the stack cleanly and with ease. We were impressed! Then, we cut a paperback book, and the HFS did the job, leaving the edges of the pages straight and clean.

It’s almost a sure bet that when running pipe and wire in an old house, you’re bound to hit embedded nails when boring the holes. That’s where these bits come in. They’re thicker than the typical spade bit to resist bending, and they have a bevel on their cutting surfaces suitable for both wood and metal.

These hole saws are known as bimetal types because they're made from two types of steel. The body is made from spring steel and formed into a cup. Around the front edge of that cup is brazed a circular row of cutting teeth made from a narrow band of high-speed steel. The result is a light weight and durable accessory tough enough to make big holes in wood  or metal. Suppose you need to make a door knob hole in a wood door; turn to these. Use them again to make holes in steel, for a tool rack, say.

Guillaume Massiquot patented the first paper cutter in 1844; however, one of the first models was built in 1837 by Thirault. His paper cutter design featured a flat surface with a fixed blade.

Big HolesIf you need to make large-diameter holes—something between ¾ inch and 4 inches, let’s say. You don’t want a drill bit, you want a hole saw. Even though these aren’t drill bits, we’ve included a set of these at the bottom of this review. It’s reasonably priced and can serve both homeowners and professional users.

Our actual testing process was relatively straightforward. We set the paper cutters up, assembled those that required assembly, and then checked to ensure all the parts were working as intended. Then we started cutting…

There’s no need to spend a lot for a quality paper cutter. This affordable model, made by Carl, boasts an 18-inch cut length and cuts up to 10 sheets of paper at once. It features a sharp blade that allows for clean, precise cuts, and it can slice through plastic sheeting, mat board, and photographs as well as paper.

Paper cutters have very sharp blades that can cause serious injury if not used correctly. Selecting a model that includes a variety of safety features to prevent accidental injury is essential. One primary safety feature to consider is a locking latch for the arm of a guillotine or stack paper cutter. This will keep young children and others from touching the blade and possibly being injured. Guillotine paper cutters should also have a tension spring, sometimes called a safety spring, that prevents the blade from coming down unless it is pulled.

Image

Overall, this paper cutter is a high-quality product that will hold up well to frequent use. Still, due to the inherent safety risks, we’d suggest limiting its use to home offices, craft rooms, or other areas with adult supervision.

Guillotine paper cutters are available in various sizes to accommodate situations ranging from cutting large sheets of stiff construction paper to trimming thin copy paper. In these instances, they can cut up to approximately 30 sheets of paper at once. Another benefit of guillotine paper cutters is they can easily cut through thicker items, such as card stock or poster board.

The blade on a guillotine paper cutter is located on one side of the base, and most cutters of this type come with a safety latch that secures the blade in the closed position to prevent accidental injuries.

Here comes the big boy of paper cutting! The first thing we noticed about this model was its weight—a beefy 35.5 pounds. That heft plus large rubber feet keep the cutter from sliding during use, and such stability is necessary for cutting thick stacks of paper.

In addition, many of the newer-style paper cutters come with popular paper-size guidelines on the cutting mat, so users can quickly cut a standard 8-by-12-inch letter-size sheet or a 4-by-6-inch photo size. These guidelines often appear in ANSI measurements, but some can be found in European Standard (DIN) metric measurements.

Suppose your drill doesn’t have a hammer function or you lack a dedicated masonry drill, what do you do then? Well, if your masonry hole drilling is confined to brick, concrete block, or mortar, you can use these inexpensive carbide-tip rotary drill bits for masonry. They won’t stand up to use in a hammer drill, but they work perfectly well, if slower, in a standard drill or cordless drill driver. Bonus: Their double-flute design allows better clearing of dust and chips compared to a single-twist type. This way you can use the drill’s high-speed setting to get through the job faster. Note that there are multiples of the smaller diameters, such as the 3⁄16-inch size, which are more frequently used with masonry screws.

If your drill driver has a hammer setting, chuck in one of these bits and make a clean and fast hole in concrete, brick, concrete block, or mortar. You don’t need an extensive set of masonry bits; a basic carbide-tip kit like this one is a great choice. Its German-made quality should provide years of use, and its slim, vinyl wallet enables it to slip into a crevice in your tool box. Carry this and you’re prepared for tough, masonry drilling jobs without having to make a quick run to a hardware store or home center.

The rectangular guides on the cutting mat of the 534 are listed in DIN sizes (millimeters), which are slightly off from the sizes most Americans are familiar with. For example, on the 534, we found a rectangular guideline for A4-size paper labeled 210 by 297 millimeters. While this is similar to U.S. letter-size paper that measures 8.5 by 11 inches, A4 paper is about .24 inches narrower and .5 inches longer. Rulers at the top and bottom of the cutting mat, however, offer both millimeters and inches.

Use: Concrete, brick, mortar, concrete block | Type: Hammer-rated carbide-tip twist drill | Number of bits: 7 | Size range: 3⁄16 to ½ inch

This model can be fitted with 11 different cutting blades (sold separately), including a perforated blade for creating a tear-off section or a scalloped blade for a pretty border on gift cards or scrapbook entries. We would have liked a magnet bar, such as those included with some of the other cutters we tested, which helps hold paper securely, but for the price, this is a good option for crafters, home offices, and homeschools.

Like the other Dahle cutter we tested, the 554 features metric DIN measurements and guidelines—but it also boasts ANSI measurements and template guidelines. This is a very nice paper cutter, and we were impressed by its performance and safe-use aspect.

One of our primary goals was to establish how easy it was to align the paper using markings or grids on the tool’s cutting bed. We also focused on how well the device cut the maximum number of sheets based on the manufacturer’s claims, and we noted whether the cutter offered guidelines for making common-size cuts. By the time we finished testing, we’d cut through four entire reams of printer paper, plus a ream of card stock, dozens of poster boards, and even a paperback book. Yes, one model was advertised as being able to cut through a book, so we tested it, and it sliced the book in half cleanly.

In testing the cutters, we discovered that some functions are more important than others. Unfortunately, not all the models we tested earned a spot on this lineup, and you can find which ones didn’t make the cut (pun intended) under “Also Tested” below.

Two types of metal are most commonly used to craft a cutting blade: steel and titanium. Steel is very durable and inexpensive; however, it will need to be sharpened regularly to keep the edge. Many of today’s guillotine cutters have self-sharpening blades—with every cut, the blade’s edge skims the steel base at an angle that helps keep the blade sharp.

Paper cutters come in four main types: rotary, guillotine, stack, and electric. Each type offers different features and is best suited for specific tasks. Understanding the uses and applications for each of these types can assist shoppers in selecting the best paper cutter for their needs.

Image

For accurate, precise cuts in a traditional guillotine cutter, check out Swingline’s ClassicCut model. This cutter is billed at being able to cut up to 15 sheets of paper at once, and we can verify that it does that very well. In fact, we were able to add a few more sheets (19 total) and still get sharp, clean cuts.

First, we analyzed dozens of paper cutters designed to accomplish various cutting tasks, then selected the highest-rated models to test. We sliced through hundreds of sheets of paper (individually and stacked), card stock, and cardboard. We even chopped a book in half!

Gridlines with marked measurements are vital for creating accurate and even cuts. Consider a paper cutter with a ruler along the top or side of the gridlines to help line up each cut. Users will want to identify whether the measurements are in inches, metrics, or both so they’ll be familiar with the model they purchase. Some paper cutters also feature a fold-out expandable ruler for additional accuracy and support.

These twist drill bits are built to withstand punishment. They’re machined out of high-speed steel and finished with a wear-resistant coating. Yet their tips can be resharpened. All that is good. What’s even better is that they’re made in America and yet are priced reasonably, especially when you account for the cost of the nice sheet steel bit index that they come in. We tried them, liked them, and thought enough of them to award them our coveted annual Tool Award.

Stack paper cutters offer one of the largest cutting capacities among the types. Many stack cutters can slice through an entire ream of paper—500 sheets—at once. Rotary and guillotine paper cutters can generally only cut through up to 30 sheets of paper at once, so a stack paper cutter can save tremendous amounts of time for folks who regularly need to cut through a massive amount of paper at once.

A paper cutter can cleanly cut paper, photographs, and other items more quickly and accurately than a pair of scissors. These tools create the crisp, straight lines that crafters, teachers, homeschoolers, and a host of remote professionals often need to make daily for work or school. We wanted to know which paper cutters were truly up to the task, so we decided to test today’s top models.

This oversize paper cutter offers everything we can envision a teacher might need when cutting paper, card stock, and photos. It features a precise cutting blade, and because it doesn’t have a guillotine bar, it may be a safer option for students.

Deirdre Mundorf is a former teacher turned freelance writer who most enjoys working with topics pertaining to home, family, and pets. She began freelance writing in 2019, after the birth of her first child, and has been contributing to BobVila.com since 2020.

This was the first rotary cutter we tested, and we were impressed. While this is a relatively lightweight cutter—it weighs just 1 pound—it came with rubber stoppers on the bottom that held it firmly in place during cutting. The cutting bed is 18.18 inches long by 9 inches wide and comes with rulers along all four edges. Even better, it features alignment markings for common size cuts, such as 4-by-6-inch photos and 5-by-7-inch photos, as well as letter size, legal size, and more.

Paper cutters are certainly handy tools. They accurately and cleanly cut through multiple sheets of paper at once to assist with crafting needs and tasks for teaching, making presentations, and other purposes. If you still have questions about paper cutters, take a moment to read through these frequently asked questions and their corresponding answers.

Use: Thin-gauge steel, aluminum | Type: Impact-rated step drill | Number of bits: 3 | Size range: ⅛ to ⅞ inchThey call these step drills because of their shape. Each step increases the hole diameter. You just stop drilling when you reach the appropriate hole diameter at the step that produces it. Although these bits are designed for sheet metal, they will drill a clean fast hole in heavier-gauge materials like electrical boxes and even mild steel channel, and shapes like L, U, and T.

A slight downside: The magnetic bar guide didn’t have much holding power. The magnet seemed weak, and a slight bump would cause the bar to slide out of alignment. Fortunately, the magnet bar isn’t necessary since the Carl paper cutter has the locking rail that holds the sheets when cutting. We consider this a good multipurpose cutter for regular paper, card stock, photos, and even cardboard, but we would limit the number of sheets to around 25 for the best results.

We’re committed to testing and reviewing products so you can make an informed decision. Advertising does not influence our product reviews and it never will. We always focus our coverage on standout products and never hesitate to mention their flaws and quirks. By using our affiliate links, you’re supporting our work and helping us continue to provide expert analysis. Find out more about our product evaluation process.

Some electric paper cutters are also programmable. With these models, users can create and save different cuts for future use by programming a set of steps for the paper cutter to follow to create the desired finished product.

If you’re getting interested in woodworking, this inexpensive brad point bit set is an easy choice. The sharp tip on these bits make it easy to start the bit exactly where you need it, and their geometry—somewhere between a twist drill and an auger bit—makes for good chip ejection.

This rotary paper cutter by Firbon is designed to cut through various materials typically involved in scrapbooking projects, including paper, cards, scrapbooking mats, and laminated items. The usable portion of the cutting bed measures 12 inches long by 4 inches wide, and the ruler at the top and the bottom of the bed offer both ANSI and DIN measurements. A foldout ruler along the side extends the cutting width to 13.5 inches for larger projects. The Firbon also has handy angle guides for making various common cut sizes.

Image

Nonslip feet are another safety feature on a paper cutter as they will keep the cutter from sliding around during use, hopefully reducing the risk of injury.

Articles may contain affiliate links which enable us to share in the revenue of any purchases made. Registration on or use of this site constitutes acceptance of our Terms of Service.

The cutting bed features solid wood for an old-school look and a grid that makes it simple to align the paper squarely. The ruler along the top offers measurements in both ANSI and DIN.

The manufacturer claims this cutter can handle up to 36 sheets of paper. We verified that in our tests, but at 36 sheets, the very ends of the cut edges were just slightly uneven. When we reduced the number of sheets to 25, the cut edges were clean with no pulling or tearing. The base alignment grid helps ensure precision and includes measurements for cutting common items, such as photographs and standard paper sizes. Rulers along the side, top, and bottom feature both ANSI and DIN measurements.

Use: Wood | Type: Forstener | Number of bits: 8 | Size range: ¼ to 1⅜ inchesWhen you need a perfectly round hole in wood with a smoothly machined sidewall, then you want a Forstener bit. These are best used in a drill press, but the smaller-diameter bits can be used in a hand drill.