Technical drawings are sometimes used by engineers to communicate specific manufacturing requirements to the machinist. If you are interested in the topic, read this article about how, when and why to use technical drawings.

To achieve maximum relative positional accuracy, two features must be machined in the same setup. This is because the new calibration step introduces a small (but non-negligible) error.

T-slot cutting tools are made of a horizontal cutting blade attached to a vertical shaft. The width of an undercut can vary between 3mm and 40mm. We recommend using standard sizes for the width (i.e. whole millimeter increments or standard inch fractions), as it is more likely that an appropriate tool is already available.Â

To remove material, the cutting tool approaches the workpiece directly from above. Features that cannot be accessed in this way cannot be CNC machined.

What are the different types of threads for manufacturing? In this article, learn how to correctly design threads to reduce lead times and cost for your next CNC machining production run.

CNC-machined parts have high dimensional accuracy and tight tolerances. CNC is suitable for both high-volume production and one-off jobs. In fact, CNC machining is currently the most cost-effective way of producing metal prototypes, even compared to 3D printing.

What is Geometric Dimensioning and Tolerancing (GD&T) and how is it used? This article explores the basics of how and when to use GD&T to get the best results out of custom part manufacturing.

Holes with a non-standard diameter must be machined with an end mill tool. In this case, the maximum cavity depth restrictions apply and the recommended maximum depth value should be used. Holes deeper than the typical value are machined using specialized drill bits (with a minimum diameter of 3mm). Blind holes machined with a drill have a conical floor (135-degree angle), while holes machined with an end mill tool are flat.There is no particular preference between through holes or blind holes in CNC machining.

Reviews from some of our clients who rank TTP HARD drills as the best cobalt drill bits for drilling harder metals including stainless steel.

Deep cavity milling: Cavities with depths greater than six times the tool diameter are considered deep. A tool diameter-to-cavity depth ratio of up to 30:1 is possible using specialized tooling (maximum depth: 35 cm with a 1-inch diameter end mill tool).

Five-axis CNC machining allows the tool to remain constantly tangential to the cutting surface. The tool paths can be more intricate and efficient, resulting in parts with better surface finish and lower machining times.

Submit a technical drawing with your drawing if your design includes threads, tolerances, surface finish specifications or other notes for the machine operator.

Have parts you need CNC machined? Upload your designs and our DFM tool will suggest optimizations and provide instant pricing.

Undercuts are features that cannot be machined using standard cutting tools, as some of their surfaces are not accessible directly from above.

In this article, we offer a comprehensive guide to the best design practices for CNC machining. To compile this extensive up-to-date information, we asked for feedback from industry experts and CNC machining service providers. If you are optimizing for costs, check out this guide to designing cost-effective parts for CNC.

End mill tools have a limited cutting length (typically 3–4 times their diameter). Tool deflection, chip evacuation and vibrations become more prominent when cavities have a smaller depth-to-width ratio.

CNC machining is a subtractive manufacturing technology. In CNC, material is removed from a solid block using a variety of cutting tools that rotate at high speed—thousands of RPM—to produce a part based on a CAD model. Both metals and plastics can be CNC machined.

Engraved text is preferred over embossed text, as less material is removed. Using a minimum size of -20 sans -serif font (e.g. Arial or Verdana) is recommended. Many CNC machines have pre-programmed routines for these fonts.

There are two main types of undercuts: T-slots and dovetails. Undercuts can be one-sided or double-sided and are machined using special tools.

Most machine shops can accurately machine cavities and holes using tools down to 2.5 mm (0.1 inches) in diameter. Anything below this limit is considered micro-machining. Specialty tools (micro-drills) and expert knowledge are required to machine such features because the physics of the cutting process change with this scale. Unless absolutely necessary, the recommendation is therefore to avoid them.

This website uses Google Analytics to collect anonymous information such as the number of visitors to the site, and the most popular pages.

CNC offers great design flexibility, but there are a few restrictions. These limitations relate to the basic mechanics of the cutting process and mainly concern tool geometry and tool access.

If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.

Image

Align the main features of your design with one of the six principal directions. If that is not possible, 5-axis CNC machining is an option.

If you add a technical drawing, please make sure it matches the specifications of the files uploaded. If the technical drawings do not match the files uploaded or the quote specifications:

It will simplify production if you design parts that can be CNC machined with the tool that has the largest possible diameter and the shortest possible length.

Using the recommended value for internal corner radii ensures that a suitable diameter tool can be used and aligns with guidelines for the recommended cavity depth.Increasing the corner radii slightly above the recommended value (e.g. by 1 mm), allows the tool to cut following a circular path instead of a 90 angle. This is preferred as it results in a higher quality surface finish. If sharp 90-degree internal corners are required, consider adding a T-bone undercut instead of reducing the corner radius.

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.

That said, 5-axis CNC has its limitations. Basic tool geometry and tool access limitations still apply (for example, parts with internal geometries cannot be machined). Moreover, the cost of using such systems is higher.

In this complete guide to designing for CNC machining, we've compiled basic & advanced design practices and tips to help you achieve the best results for your custom parts.

This is Wayne Winton with Tri County Locksmith Service. I have used the TTP-HARD-drills and personally feel they are some of the highest quality drill bits I have ever used. They work well on a variety of  steels from hardened spring steel to brass and aluminium, all with fast cutting speed and easy drill point starting. They are far superior to the average drill bits that can be purchased at the local hardware store. They have put much time and research into their product and it shows in pure performance. These drill bits are in my service truck and will be for a long time.

A 5-axis CNC machine moves cutting tools or parts along five axes at the same time.  Multi-axis CNC machines can manufacture parts with complex geometries, as they offer two additional rotational axes. These machines eliminate the need for multiple machine setups.

As material is removed from the workpiece, the geometry of the tool is transferred to a machined part. This means, for example, that the internal corners of a CNC part always have a radius, no matter how small a cutting tool was used.

The technical drawings are considered the point of reference for the thread specifications, tolerance specifications, surface finish details, part marking requests and heat treatment specifications.Â

Have you designed your parts with sharp corners? They may look good on paper, but they're a nightmare to manufacture with CNC machining. In this article, learn how and why to avoid sharp corners in your designs. It'll reduce lead times, cost and potential headaches for machinists.

The total number of machine setups affects the cost. Rotating and realigning the part requires manual work and increases total machining time. This is often acceptable if the part needs to be rotated up to three or four times, but anything above this limit is excessive.

What are the different types of heat treatment and how do they affect CNC-machined parts? This article explores how heat treatments can be applied to many metal alloys to drastically improve key physical properties like hardness, strength and machinability.

Image

I had already wasted a mix of various ten HSS, Tungsten and Titanium coated drills without even successfully drilling one hole and was running out of ideas. After trawling the internet I came across the TTP drills and was so impressed with the video I ordered a selection of sizes to try them out. What a difference! A firm pressure and some jiggling with the drill speed soon resulted in the drilling of all the holes with one drill and with the same curl of swarf seen on the video. The other drills produced dust, if I was lucky.

In this complete guide to designing for CNC machining, we've compiled basic & advanced design practices and tips to help you achieve the best results for your custom parts.

They are fabulous. I still haven’t had the time to use them for their actual intended purpose – drilling out exhaust manifold studs, but I did try them out on a couple of bolts to see how they did and was very impressed! Told a bunch of my friends about them. Hoping to get a joint order together. I want more sizes or one of the sets!

Image

Best drill bits I’ve ever used by far, I purchased several different cobalt bits trying to drill into a broken cylinder head bolt to extract it and not one would do more then scratch the hardened head bolt. After hours of trying to drill into the broken bolt I decided to go online and find a different type of bit, after watching many videos about these bits I decided to purchase a full set with their ‘in house lubricant’ as well. Within 10 mins I had the broken bolt drilled and extracted, I’ve never seen a bit cut hardened steel that effortlessly before, I am a life time customer from here on out, worth every penny. Thank you

TTP may sell tough products but I found them anything but tough to deal with, communications were excellent and the drills arrived on time and well packaged. I would deal with them again without hesitation and can highly recommend their products and service. Thanks TTP.

This comprehensive guide compares the 25 most common materials used in CNC machining and helps you choose the right one for your application.

Holes are machined using either a drill bit or an end mill tool. The size of the drill bits is standardized (in metric and imperial units). Reamers and boring tools are used to finish holes that require tight tolerances. For high-accuracy holes with a diameter smaller than 20 mm, using a standard diameter is recommended.

Just to let everyone know these drill bits are BRILLIANT, it is the first time I have ever worked with metal and was using Bosch titanium bits, managed 3 holes with 3mm drill bits. Then I ordered TTP bits and they were like a hot knife through butter. I was drilling 1cm hard steel and the job was so easy. Highly recommended, don’t buy expensive imitations.

For standard tools, the typical ratio between the cutting diameter and the diameter of the shaft is 2:1, thereby limiting the cutting depth. When a non-standard undercut is required, it is common practice for machine shops to manufacture their own custom undercut tools. This can add to lead time and cost, so avoid it if possible.

Hello there….I just thought I’d drop you a line commending your products. The 6,5,4 and 3 mm drill bits work a treat on my stainless steel cycle rack. Initially I ran the drills too fast and I didn’t use enough pressure which resulted in poor performance, particularly on the larger drill sizes. I quickly learned that slowing the drill down and increasing drill pressure whilst ensuring enough cutting grease had been applied enhanced the drilling performance immensely. It used to frighten me when drilling stainless steel. NOT ANY MORE! Well done your Company!

How do you prepare technical drawings for CNC machining and why are they important? Technical drawings are widely used in manufacturing to improve the communication of technical requirements between the designer and engineer and the manufacturer.

When designing parts with undercuts on internal walls, remember to add enough clearance for the tool. A good rule of thumb is to add space equal to at least four times the depth of the undercut between the machined wall and any other internal wall.

For threads in blind holes cut with taps (i.e. all threads smaller than M6), add an unthreaded length equal to 1.5 times the nominal diameter at the bottom of the hole. When a CNC threading tool can be used (i.e. threads larger than M6), the hole can be threaded throughout its length.

What is anodizing? Anodizing is key to finishing parts made from aluminum and other metals. Learn how anodizing works and why it is an important part of CNC machining and manufacturing.

I was very happy with my purchase of the tough drill bits , they allowed me to drill out some broken off tensile bolts from a 25 year old motorbike cylinder head , failure in this would have meant finding a new head or abandoning the project

Make the most of CNC machining by optimizing your design and making the right material choices. Read these 14 design tips to help you reduce CNC-machining costs and create the perfect parts for your project.

We recommend aligning all your model’s features (holes, cavities, vertical walls, etc.) to one of the six principal directions. However, see this rule as a recommendation and not a restriction, as 5-axis CNC systems offer advanced workpiece-holding capabilities.

Our tolerances are either 2768 medium or fine. If tolerances are not specified, manufacturing partners will use the selected 2768 grade.Tolerances define the boundaries for an acceptable dimension. The achievable tolerances vary according to the base dimension and the geometry of the part. The values above are reasonable guidelines.

A challenge that frequently comes up while designing a part for CNC machining is that no industry-wide specific standards exist. CNC machine and tool manufacturers continuously improve the technology’s capabilities, expanding the limits of what is possible. The table below summarizes recommended and feasible values for the most common features encountered in CNC machined parts.Â

Design for manufacturing (DFM) means taking a design-first approach to manufacturing. In this article, we look at the overall DFM process, the necessary steps for a successful outcome, examples of DFM done right and how to get the most out of your own processes.

They are amazing. Didn’t believe the hype, but it appears to be true. I am a locksmith and drill hard plate on safes. They really tore into it.

The majority of the load applied to a thread is taken by the few first teeth (up to 1.5 times the nominal diameter). Threads longer than 3 times the nominal diameter are thus unnecessary.

Decreasing the wall thickness reduces the stiffness of the material, which increases vibrations during machining and lowers the achievable accuracy. Plastics are prone to warping (due to residual stresses) and softening (due to temperature increase), so a larger minimum wall thickness is recommended. The feasible values stated above should be examined on a case-by-case basis.

End mill tools have a flat or slightly rounded lower cutting edge. Other floor radii can be machined using ball end tools. It is good design practice to use the recommended values, as it is preferred by the machinists.

There are a few easy steps you can take to optimize your designs for computer numerical control (CNC) machining. By following design-for-manufacturing (DFM) rules, you can get more out of CNC machining's broad capabilities. This can be challenging though, as industry-wide specific standards do not exist.

I broke two stainless bolts in the head of my ex-US Army jeep engine which defied left hand bits, quality HSS right hand bits, gas and brute force. They were just an inch long and eventually we got a small pilot hole and a pile of blunt drills. I read that cobalt drills were worth trying, found the TTP site, saw the videos and ordered two of two sizes (in case they got blunt?). A decent-ish corded drill and a single TTP just sliced through both bolts using plenty of oil and low speed as advised in the vid and info leaflet. After a wipe with a rag the drills went in the tool box – though I couldn’t tell which was the used one and which was unused. It sounds corny but I should have got the TTP drills earlier and saved a lot of time and hassle.

Tool access is also an issue when machining features with a large depth-to-width ratio. To reach the bottom of a deep cavity, for example, you need tools with extended reach. This means a wider range of motion for the end effector, which increases the machine chatter and lowers the achievable accuracy.

Threads are cut with taps and external threads with dies. Taps and dies can be used to cut threads down to M2. CNC threading tools are common and are preferred by machinists, as they limit the risk of tap breakage. CNC threading tools can be used to cut threads down to M6.

Tool access is one of the main design limitations in CNC machining. To reach all surfaces of the model, the workpiece has to be rotated multiple times.Â

For dovetail cutting tools, the angle is the defining feature size. Both 45- and 60-degree dovetail tools are considered standard. Tools with an angle of 5-, 10- and up to 120-degree (at 10 degree increments) also exist but are less commonly used.

We sent our drill bits to renowned locksmith Wayne Winton from Tri-County Locksmiths in Colorado to see what he thought of them. Here are just 2  of the videos he posted on Youtube.

We don’t usually require a technical drawing for orders on our platform, but in some cases, they can add valuable context to a quote request. Certain design specifications cannot be included in a STEP or IGES file. For example, you’ll have to include a 2D technical drawing if your model includes threaded holes or shafts and/or dimensions with tolerances tighter than the selected 2768 grade.