Spot the local: Qld’s arts industry could do with a bit of home-grown

Horn's SG3 coating is designed for machining titanium alloys and superalloys, as well as for hard turning and hard grooving applications. It can withstand temperatures of up to 1100°C and is designed to deliver high performance when working with materials that are difficult to machine. Now that the advantages of the tool coating have been proven on selected Horn tool systems, the 105 Supermini grooving and boring system products are available from stock.

Transport, Energy and Infrastructure Department project manager Jim Zissopoulos says all affected traders in the community have been consulted, with positive results.

A number of accidents have occurred on the bend, known as Mill Corner, and Loxton Waikerie Council has been calling for the road's realignment for many years.

The design phase in the redevelopment of a dangerous section of road at Loxton is almost complete, after an extensive community consultation process.

A new, modular system for reaming large diameter holes has been introduced by Horn and will be on show for the first time in the UK at Mach 2022 in Hall 20, stand 340. Offering high precision, flexibility and easy handling, DR-Large reamers have exchangeable cutter heads with multiple solid carbide inserts, resulting in high cutting values, short cycle times and low costs. The interface of the insert seats has been designed to offer precise interchangeability to within a few microns and tool setting is unnecessary when exchanging the cutter head.

The substrate and geometry of Horn's 304 circular interpolation milling system can be easily matched to the machining process. (Source: Horn)

"The requirements of the traders in relation to access to their property was achieved while at the same time achieving the transport objectives of improved safety and improved road performance, so at this point now we'll go on to complete the design and from there go on to construction later in the year," he said.

This portal is a brand of Vogel Communications Group. You will find our complete range of products and services on www.vogel.com

Horn's SG3 coating is designed for machining titanium alloys and superalloys, as well as for hard turning and hard grooving applications. (Source: Horn)

We acknowledge Aboriginal and Torres Strait Islander peoples as the First Australians and Traditional Custodians of the lands where we live, learn, and work.

Horn’s DS system for dynamic HPC milling excels at dynamic roughing as well as during standard roughing cycles. (Source: Horn)

This service may include material from Agence France-Presse (AFP), APTN, Reuters, AAP, CNN and the BBC World Service which is copyright and cannot be reproduced.

Making its UK debut will be Horn's expanded DS range of solid carbide end mills with a new geometry for HPC (high-performance cutting) milling of high strength steels at elevated material removal rates. It particularly excels in dynamic roughing applications as well as in standard roughing cycles. Different helix angles create an irregular tooth pitch, making operation exceptionally smooth. The end mills are available in diameters from 2 mm to 16 mm as standard, with four or five flutes.

The Horn circular milling system offers users many advantages, including a high level of reproducible quality. It is fast, reliable and achieves good surface finish. During processing, the tool plunges into the material either at an angle or horizontally and is interpolated either in a circle, or helically to produce a thread.

UK — At Mach 2022, Horn will present a modular system for reaming large diameter holes, an extended range of products for circular interpolation milling of holes down to 8 mm diameter, two new, high-performance coatings as well as an expanded range of solid carbide end mills.

The inserts are available in widths of 0.5 mm, 1 mm, 1.5 mm and 2 mm. For milling circlip grooves, Horn offers the system with cutting widths of 0.8 mm, 0.9 mm, 1.1 mm and 1.3 mm. In the case of the full radius versions, radii of 0.4 mm, 0.6 mm and 0.8 mm are offered. To enable the milling of chamfers, angles of 45, 30 and 15° are available. Regarding the substrates, Horn uses coated grade EG55 for general steel machining and IG35 for machining stainless steels and superalloys.

Reaming is an economical machining process. Compared to boring holes to tight tolerances, it is faster and can significantly reduce cost of production. Until now, reaming tools on the market in these larger sizes have been either special brazed tools or diameter-specific reamers with fixed inserts. With such tools, which tend to be delicate and heavy, replacing worn inserts is a complex process and calibration can be tricky for many users. Horn offers a practical alternative with its exchangeable-head, pre-calibrated DR-Large reaming tools and its customer service department offers quick and simple reconditioning.

At the exhibition, Horn will explain the importance of two new, high-performance coatings, IG6 and SG3, it has introduced for the manufacture of carbide inserts used in turning applications. Despite being less than 0.005 mm thick, such coatings can extend service life by a factor of 10 or more compared to uncoated inserts.

Imprint Cookie-Manager About Media Subscription cancellation Privacy General Terms and Conditions Help AI-Guidelines

In evidence also at the show for the first time will be Horn's extended range of products for circular interpolation milling of holes down to 8 mm diameter. The triple-edged 304 system offers a versatile, productive solution for internal groove, thread and profile milling as well as finish boring and chamfering. The insert has a cutting diameter of 7.7 mm. In conjunction with various vibration-damping carbide shanks, which feature an internal coolant supply, the tool is more economical and versatile than solid carbide milling cutters for machining smaller diameters.

IG6 is a copper-coloured, aluminium-titanium-silicon nitride (AlTiSiN) coating for machining steels in groups P and M with Horn's S224 and S229 grooving systems. In conjunction with an adapted carbide substrate, the coating allows faster material removal rates and significantly extended service life. Standard inserts are available from stock, while for special designs, Horn Greenline orders can be delivered within five working days of the customer signing off on the drawing.

The versatile, interchangeable reaming system is suitable for bore diameters from 140 mm to 200.2 mm. Six cutter heads cover the range of diameters in 10 mm increments, with two sizes of head fitting on each size of reamer shank. Modular construction and an ABS-compatible interface means the tool can be extended to any length, in theory without limit. All reamers are equipped with direct internal coolant supply to each cutting edge.

The tools’ optimised face geometry reduces the cutting pressure during linear or circular ramping. Improved chip spaces ensure optimal process reliability during chip formation and removal. The system also demonstrates good performance during finishing. Smooth operation means that high surface quality can be achieved during side milling, for example. HPC milling of high strength steels at fast metal removal rates places significant demands on the tools. New carbide substrates and new tool coating technologies make this process feasible. Horn relies on the ES3P grade, again with a HiPIMS coating.