There are actually a handful of drill point angles, but 118º and 135º are the two most common. A 118º drilling point is commonly put on lower-cost, general-purpose drill bits. It’s suitable for mild steel, aluminum, and other soft metals. On the other hand, 135º is for hardened steel and other tougher materials.

Solid Carbide drill bits are the most expensive but they will outlast other drill bit materials by a longshot.  A Carbide drill will outlast a Cobalt drill by at least twenty times, reducing the cost-per-hole significantly.

As we said earlier, every manufacturer has its own special sauce when it comes to drill bit design but the high-level points we covered here are universal. We hope that this condensed guide will serve as a foundation and help you understand what to consider when choosing the right drill bits for your upcoming jobs.

If you have any questions at all, please feel free to reach out to our team at (833) 4-ETOOLS. You can also email us at sales@eldoradotools.com.

AlTiN is a couple of steps up from TiN, with extended life and performance. An interesting charismatic is that these do not perform well on aluminum since aluminum is part of the coating.

A shorter drill bit is more rigid which is ideal so you should always use the shortest drill possible. That said, sometimes you have to use a longer drill bit. In these instances, you should at least use the shortest flute-length (cutting portion) possible. Using a drill with an unnecessary long flute length means that you’re choosing to use a less stable drill. This is not advised. The next question to ask is, “How much flute length do I need?” The rule of thumb for determining this is to take the diameter of the drill bit, double that, and then you’ll have the minimal flute length needed above the hole for proper chip evacuation.

One characteristic of Carbide is that it’s brittle, so it won’t flex. This makes Carbide a bad choice for hand drilling. If you’re running a CNC or frequently use a drilling press, this material is worth the investment.

Image

Black and Gold finish drill bits resist corrosion and breakage while increasing lubricity. These bits are not prone to chipping and flaking.

For quick access to all degrees of high speed steel tapered endmills, use the direct links below. Do not hesitate to call if you have any questions regarding our cutters or the use of a specific tapered end mill. 888.531.8500.

Throw a good coating on any drill bit and you’ll completely change its characteristics. Coatings extend tool life and improve cutting performance. We’ve selected a few of the most popular coatings to keep things simple, so let’s jump in.

This is an excellent and underappreciated feature in twist drills. A split-point drill bit prevents walking when starting a cut. Without a split-point, technicians would first need to drill pilot holes or use punches in order to start their cuts. This would, of course, take a lot more time and cut into your bottom line.

The first thing to think about is the composition of the drilling bit. There are three popular composites and they all serve a different purpose.

Black Oxide finishes increase lubricity which helps to resist damage from heat and corrosion. Naturally, this also extends the life of the tool. These bits are best for use on ferrous metals.

Carbide drills allow for a Through Spindle Coolant system or TSC as it’s known. In situations where you’re drilling deep into very hard materials, the feeding of coolant through the drill allows for better chip evacuation and self-cooling. This also helps to prevent wear, which is nice since TSC drill bits are pricey.

Geometry is just as important as the material and coating when it comes to the performance and characteristics of a drill bit. Consider that every manufacturer has its own proprietary configurations so we’ll just focus on the general aspects.

We're an online retailer, headquartered in Lakeway, Texas. With fulfillment centers distributed throughout the United States, we guarantee fast delivery!

Our 1.5 degree tapered end mills are made from premium grade high-speed steel and improve both machine time utilization and finish during the milling of draft angles and slotting of tapered walls. By reducing the need for multiple end mills to perform multiple processes, milling time is reduced and parts per tool are increased.

Image

When it comes to choosing the right drill bit for the job, there are three things to consider; material, coating, and the geometry of the tool. We’ll break it all down in a concise way to help clear things up to save you some time.

Skinny drill bits snap more easily than thick drill bits. This is where spending a little more money for heavy-duty geometry is nice. That said, there is much more to drill design than the thickness and it’s not always a priority but it is a nice thing to be aware of.

High-Speed Steel (HSS) is the most popular drill bit material for several reasons. High-Speed Steel is readily available, and we have plenty of it right here in the United States. HSS is also extremely versatile. Manufacturers can configure an HSS drill bit for just about any application you can think of.

A critical feature in twist drills, helix angles determine the process of chip formation. Large helix angles are good at removing soft, long-chipping materials. Small helix angles are good for the removal of hard, short-chipping materials. Note that there is some overlap in how helix angles are categorized.

Image

M42 Cobalt is high-speed steel with 8-10% Cobalt added in order to increase the hardness and endurance of the tool. You can pretty much expect the same characteristics as a standard HSS drill, but with increased performance across the board.