The trainers were SO effective. They were clearly very excited and passionate about the content. They really embodied the Pinnacle method and were also very good at providing both positive and constructive feedback.

Performancepartscompany

Feeds and speeds are critical parameters in machining operations. Feeds refer to the rate at which the cutting tool advances through the material, typically measured in inches or mm per minute, and are essential for balancing material removal rates with effective chip clearance. Inadequate feed rates can lead to tool breakage or chip clogging. Speeds concern the spindle RPM (revolutions per minute), influencing tool temperature and wear. Proper spindle speeds prevent the tool from overheating, which can soften and dull the cutting edge, resulting in poor surface quality or tool failure. Both feeds and speeds are vital for optimizing tool life, enhancing machining efficiency, and ensuring superior surface finishes

Dance Fusion Morley

Image

Dance Fusion schedule

How we do this – Using neuroscience-based research and actor-based training, the Pinnacle experience forges confident, effective communicators through:

The selection of the DOC and WOC must balance efficiency and the need to minimize tool wear and potential damage to the workpiece. Deep cuts in the axial and radial axis can be more efficient but might lead to higher forces on the tool and workpiece, while shallow cuts are generally less efficient but can achieve better surface finishes and extend tool life.

Image

Content, practice sessions and pattern interrupts. This was a fantastic training with a ton of interaction. The structure was great for practicing in a safe environment and applying feedback in the moment. Connor and Jim are amazing trainers. I would highly recommend this course.

Dance class Morley

ThePerformance CompanyMorley

Feed per tooth is the amount of material removed by each tooth of the cutter during one spindle revolution. This is usually measured in millimetres per tooth or inches per tooth. The appropriate value depends on the material being cut (such as metal, plastics, or plywood) and the type of cutter used (e.g., coated or uncoated carbide). You can typically find this information online.

DOC stands for Depth of Cut and is the depth the tool penetrates the material along its axis, perpendicular to the surface being machined. It's usually determined by the cutting-edge length of the tool and how much of the tool is engaged with the material.

Why we do this – Because boring is everywhere. Useless meetings, dull presentations, and pointless ramblings eat up valuable time and destroy morale. Lead your company on a journey toward compelling and influential communication by investing in your people.

The instructors were credible and displayed all of the techniques we were learning in their own presentations so it was obvious they were now a very natural part of their approach; this gave me confidence that the techniques will work.

Dance Fusion

The trainers did an incredible job! They were fantastic communicators, everything was very understandable and easy to follow. It was one of the first trainings/courses that I have taken that kept my attention the entire time. The breakout sessions were very helpful and as was their feedback. The whole course was very well run and smooth.

It hits the bullseye when someone who is teaching the skill is not giving you checklists, but doing the same and showing you how it’s done. The presentation was superbly done by orators, and just by going through how they are structuring it, and executing it, one can learn a lot about effective communication.

WOC stands for Width of Cut and it refers to the width of the material engaged by the cutting tool in the direction parallel to the workpiece surface. This depth is less than the tool's diameter.

ThePerformance Companyphotos

Image

Surface Meter per Minute (SMM), similar to Surface Feet per Minute but using metric units, indicates the speed at which the tool's cutting edge moves relative to the material's surface. Like the feed per tooth, it varies depending on the material and the type of cutter used. This data is also available online.

The content was fantastic but even more so the way it was presented. it was a true testament to the training itself and how it can pay off. 10/10

This video provides a clear guide on how to calculate the feeds and speeds for a tool. The linked website offers valuable resources, including feed per tooth and surface meter per minute values, based on the tool and stock material to assist in determining the appropriate feeds and speeds.

Now that you know how to calculate feeds and speeds, you can apply this knowledge by setting up your tool in Fusion 360 to proceed with the CAM operations. The next video demonstrates how to create your own tool library in Fusion 360.