304 SS - 304 stainless steel cutting speed

www.harveytool.com www.helicaltool.com www.micro100.com www.titancuttingtools.com www.corehog.com www.valorholemaking.com

Continuing the automotive theme, Nick Warrior of the University of Nottingham spoke about his collaboration with Ford on the AFRECAR (Affordable Recycled Carbon Fibres) and HIRECAR (High Value Composites from Recycled Carbon Fibres) projects. These projects are looking into ways of resolving the problems of meeting the requirements of the end-of-life directive (which requires that 95% of all vehicle materials must be recycled by 2015) and developing affordable composites for motor vehicles. These projects have been able to produce some ‘demonstrator’ parts by, amongst other things, incorporating fibre in bulk moulding compounds. Agreeing with the findings of the Imperial College team, Nick Warrior stressed the importance of optimum fibre alignment as the key to added value recycled composites.

Day 1 closed with two complementary presentations from researchers at London’s Imperial College. Soraia Pimento is engaged in research into analysing failure mechanisms under different stress conditions, and explained that irregular alignment and density of recycled fibres were the main causes of the reduction in strength relative to virgin fibre. Silvestre Pinho’s work built on this primary research by developing models that will enable predictions of performance to be made. This information can then inform the design of reclamation/recycling systems to give the optimum outputs.

Recyclingcarbon

Thank you for clarifying that reamers should always be used to achieve the desired tolerance when a high surface finish is required for a hole. My sister wants her factory’s production equipment to be moved by pre-programmed software and code. I’ll advise her to use CNC machining to get a high level of surface finishing.

The nature of the difficulties faced by recyclers was highlighted by Dr Jan-Michel Goseau of Adherent Technologies when he referred to carbon fibre reinforced composites as “intractable by design”. Referring to his organisation’s early attempts to recycle manufacturing scrap from a Boeing 787 he raised a laugh amongst the delegates by saying he was very confident about flying in a composite aircraft “but about recycling it, much less so!” He also revealed that Adherent plan to open a 100 ton/annum recycling facility in the near future.

Moving from the aerospace sector into motor racing, James Meredith from Warwick University outlined the role of recycled carbon fibre in World F3rst, a sustainable Formula 3 racing car. In addition to ‘non safety critical’ bodywork parts such as the engine cover being made from recycled carbon, the car has a number of other sustainable credentials including a steering wheel made of Curran® - a material derived from the pulp of root vegetables - and a seat whose is base made from a woven flax fibre prepreg material covered in SoyFoam, a soya bean derived foam.

Dr. Steve Pickering, of the University of Nottingham, both chaired the conference and gave the opening presentation. His presentation looked at the various technologies available to recyclers, and concluded that there is no ‘one size fits all’ solution: for instance, processes suitable for waste/reject goods deliver very low degradation in key fibre properties (<3% for supercritical fluid processing), whereas processes better suited for ‘end-of-life’ material may reduce strength by 25%-50% due to mechanical damage and fibre oxidation.

Our correspondent Steve Kay, is Business Development Manager at Bolton, U.K. based NW Texnet, a leading technical textiles cluster management organization.

Reamers Provide Precision – As mentioned earlier, reamers are great for machining precision hole diameters. To use a reamer properly, you must first have a pre-drilled hole that’s between 90% and 94% of the final hole diameter. For example, if you need a finished a hole of .220″, your predrilled hole should be somewhere between .1980″ and .2068″. This allows the tool to take enough material off to leave a great finish, but does not overwork it, potentially causing damage. The tolerance for uncoated reamers is +.0000″/-.0002″, while the tolerance for AlTiN coating is +.0002″/-.0000″. These tolerances provide you the peace of mind of knowing that your hole will meet exact specifications.

ELGcarbon fibre

Achieve a Quality CNC Finish – When a high surface finish is required of a hole, reamers should always be used to reach the desired tolerance. Both the pre-drilled hole and the tool’s margin help to keep the reamer centered while cutting, leading to a better finish.

As the conference closed, there was general agreement among the delegates that this should not be the last platform dedicated to the subject of carbon fibre recycling, although future editions may be incorporated into less highly specialized conferences.

Tim Rademacker of CFK Valley Stade Recycling presented a well thought out SWOT analysis of recycled carbon fibres, pointing out the fact that demand for virgin carbon fibre running ahead of supply was a real opportunity. CFK are investing heavily in carbon fibre recycling technology, with a 1000 ton/annum plant due to come on stream in autumn 2010.

Most machinists are familiar with CNC drilling, but did you know that the common practice for holemaking is to always use a reamer? When done correctly, reaming can be a fast and highly accurate operation that results in precision holes.

Pete George from Boeing’s Research and Technology division started day 2 with a look at some aircraft parts that might be made from recycled carbon. Obviously these would not include major structural assemblies, but might well be items such as armrests (a prototype was passed around the conference room) and overhead stowage bins. Pete George argued that the goal of recycling for the aircraft industry should be to reclaim material in a way that substantially retains the value and attributes of the original material and can be integrated into existing markets.

Steve Line, CEO of the West Midlands based company Recycled Carbon Fibre Ltd., told delegates that his company had the world’s first continuous commercial scale carbon fibre recycling line, and posed the question of how to establish a baseline price for recycled carbon fibre. Despite the diverse nature of the feedstock, with little or no information on the strength properties of the original fibre, RCF claim to retain upwards of 90% of the strength of typical virgin carbon fibre.

Building in additional safety, comfort and emission reduction features has increased the kerb weight of the average car by 20% since 1985, according to Bern Thoma of the Fraunhofer Institute. This makes the ‘lightweighting’ potential of composites a very attractive proposition to the industry: taking the whole of its life cycle into account, from raw material manufacturing through to recycling, around 85% of the CO2 emissions of a vehicle will come from its use, therefore even small savings in weight will have a marked effect on life cycle CO2 values.

The use of carbon fibre reinforced composites has been growing steadily for several years, and this growth looks set to accelerate in the future as technology advances open up new end uses and markets. One industry analyst forecasts this growth to be from around 170 million lbs in 2009 to somewhere in the region of 270 million lbs by 2013. However, hand in hand with this growth comes the problem of how to process both manufacturing waste and end-of-life goods in an environmentally responsible way.

Harvey Tool also offers Miniature Reamers – Right Hand Spiral. This tool is designed to leave a superior part finish and help with chip evacuation in blind hole applications.

CNC Machining Exotic Alloys: When machining Inconel, titanium, and other high-cost materials, reaming your hole is important to ensure that the desired finish specification is met. With reamers, a machinists can better predict tool life, leading to a better finished product and less scrap ratios. It is important to note that Harvey Tool reamers are offered AlTiN coated and fully stocked in every .0005” increment from .0080” to .0640”.

Business intelligence for the fibre, textiles and apparel industries: technologies, innovations, markets, investments, trade policy, sourcing, strategy...

Carbonfiber recycling companies

The first ever Carbon Fibre Recycling and Reuse Conference, organised by Intertech Pira, was held in the Bergedorf district of Hamburg in early November. Over 50 delegates from all over the world attended the one and a half day conference, which featured over a dozen presentations on subjects such as an overview of the different recycling technologies available, operational challenges, and end user perspectives. The use of carbon fibre reinf

The first ever Carbon Fibre Recycling and Reuse Conference, organised by Intertech Pira, was held in the Bergedorf district of Hamburg in early November. Over 50 delegates from all over the world attended the one and a half day conference, which featured over a dozen presentations on subjects such as an overview of the different recycling technologies available, operational challenges, and end user perspectives.

Jack Howarth of University of Sheffield (representing Technical Fibre Products) discussed ways of incorporating recycled carbon in fuel cell technologies and Electromagnetic Interference (EMI) applications, whilst concluding that many challenges lay ahead for the technology, whilst Joseph Heil of North Carolina State University updated the conference on Vacuum Assisted Resin Transfer Moulding, Bulk Moulding Compound and Injection Moulding technology.

Only by sharing the cost and investment between generator and recycler can a sustainable revenue chain by established, said Thomas Hunter of carbon fibre recycler Firebird Advanced Materials. This presentation outlined the various sources of raw material, and how the different states it arrives at the recyclers in affect the recycling process. Hunter came to the conclusion that, until a means of automated sorting can be devised, the most cost effective way to sort scrap is at the point of generation, although how to incentivise primary manufacturers to do this was a real problem.

Minimize Machining Production Runs – For machine shops, consistency is a priority. This is especially true in production runs. The last thing a machinist wants to see is an oversized hole on a part they have already preformed many operations on. Remember, reamers have the benefit of offering consistent hole size, preventing an out of tolerance finish. These consistent holes lead to valuable time savings and reduced scrap costs.

Bill Carberry, Boeing’s Airplane and Composite Recycling Program Manager, who is also a deputy director of the Aircraft Fleet Recycling Association (AFRA), made a number of interesting points. First among these, he stated that the members of AFRA recycled 220,000 tonnes of aluminium in 2008: as aluminium is replaced by (albeit lighter weight) composites in the next generation of aircraft, the carbon fibre recycling industry will be presented with a stiff challenge if it is going to keep pace with demand. Second, he stressed that whilst Boeing’s current developments were very much centred on composites, aircraft manufacturers would always use the best material available for the purpose and there was no guarantee that this will always be carbon fibre.

Iscarbonfiber bad for the environment

By examining a Harvey Tool Miniature Reamer and its critical dimensions, we can better understand the functionality of this useful tool. In the above image of a straight flute reamer, D1 references the reamer diameter, the specific size intended for your hole; and D2 points to the shank diameter. At Harvey Tool, reamer shanks are oversized to help maintain tool strength, stiffness, and accuracy. Shanks also have an h6 tolerance, which is crucial for high precision tool holders, such as heat shrink collets. Other critical dimensions of a reamer include its overall length (L1), margin length (L2), overall reach (L3), and chamfer length (L4).

Sign up to receive a monthly recap of: – The latest machining solutions – Machining tips and tricks – A recap of our most popular posts

© Copyright Innovation in Textiles. Innovation in Textiles is an online publication of Inside Textiles Ltd. PO Box 271, Nantwich, CW5 9BT United Kingdom Registered in England No 04687617