Rolling Tools purchases its raw materials directly from the best European steel mills, with which it has established a close working relationship, obtaining high quality products over time and, for some applications, steels with customised chemical compositions.

Inserts forturningplastic

suitable for rolling screw and bolt of non-hardened steel with low carbon content, stainless steel and parts with a hardness of less than 37 HRC. These flat dies can be supplied with special heat and surface treatments, developed by Rolling Tools, depending on the specific use by the customer.

With thick TiCN and Al2O3 coating, it has strong plastic deformation resistance and cutting edge strength, and is the general preferred brand for steel from finishing to rough processing. Under the condition of high removal rate cutting parameters or undesirable working conditions, it can achieve a more green and environmental dry cutting. Under the same cutting conditions, the cutting speed can be increased by more than 25%. At the same cutting speed, the insert life can be increased by more than 30%.

The nc-TiAIN coating is combined with the strong and ductile matrix of ultrafine particles, suitable for fine and semi-fine turning of various processed materials and rough turning of superalloy.

The nc-TiAIN coating combined with fine particle matrix is suitable for finishing of all kinds of materials and finishing and semi-finishing of superalloy.

PVDcoating

suitable for rolling heat treated screw and bolt of class 10.9, 12.9 or higher, parts of special alloys (i.e. Titanium, Inconel, etc.) used in the automotive and aerospace sectors, or any steels with an hardness greater than 37 HRC. These flat dies can be supplied with special heat and surface treatments, developed by Rolling Tools, depending on the specific use by the customer.

Be the first to review! CLOSED NOW. Today: 10:00 ...

Insert Turningtools

The combination of high strength and plastic deformation resistant matrix with MT-TiCN, thick Al2O3 and TiN coating has good toughness and plastic deformation resistance, which is suitable for rough machining of steel.

Image

The CVD coating brand, (thick Al2O3, thick TiCN) is combined with hard substrate, which shows good wear resistance and impact resistance during high-speed processing of nodular cast iron.

CarbideTurningInserts

Made of low carbon cold drawn steel wire · Diamond shaped sharp point for easy drive in of the nail · Available in zinc electroplated version for enhanced ...

At Magnuson Performance we specialize in lifting trucks and Jeep SUVs in-house, ensuring your vehicle has the cred to match its sleek style and impress.

Kennametalinsertguide

CNC Machining Services · Drilling. Many fastening products call for one or more holes to be drilled into the fastener body. · Milling. In CNC milling operations, ...

As an experienced manufacturer in the research and manufacturing of coated inserts, Wodenco is always ready to deliver reliable tooling products and solutions for you. Wodenco has been trusted by customers from all over the world in the past 10 years. Due to quality material, high-tech equipment, and reliable quality test system, we achieved a consistent reputation in both, domestic and overseas market. We aim to provide all the solutions that you need in the industry. Wodenco is committed to producing reliable cutting tools products and services.

CVDcoating

Sorted by Shank diameter ; 0.896, 0.672, 1-1/16" 1-1/8" ; Shank MM, Shank Inch, Square MM, Square Inch, ANSI Inch ; 23.0, 0.906, 17.0, 0.669 ...

Aug 14, 2020 — Clearance Fits. With a clearance fit, the shaft is always smaller than the hole. This enables easy assembly and leaves room for sliding and ...

The thick TiCN and Al2O3 coating can improve the impact toughness and wear resistance greatly, which is the ideal choice for high speed cutting from steel finishing to semi-finishing. The cutting speed can be increased by more than 25%. At the same cutting speed, the tool life can be increased to more than 30%.

The excellent combination of tough matrix with good edge safety and MT-TiCN, thick Al2O3, TiN coating. It is suitable for semi-finishing of steel.

Cutting tool inserts are replaceable attachments for cutting tools that typically contain the actual cutting edge. Cutting tool inserts applications include ...

The special structure matrix combined with TiCN, thin Al2O3 and TiN coating has good resistance to diffusion wear, plastic deformation and impact. It is suitable for finishing, semi-finishing and roughing of stainless steel.

The high performance TiAIN coating with nanostructure ensures the insert has extremely high toughness and hardness. The unique coating technology makes the insert have smooth surface and high wear resistance. The outstanding thermal stability and chemical stability provide effective protection for the cutting edge.

Rolling Tools pays particular attention to quality, service and customer satisfaction: essential characteristics for a constant and long-lasting relationship over time.

PVD coating brand, a new TiAIN based multi-component coating, has higher wear resistance and high temperature oxidation resistance. Suitable for all kinds of refractory alloy, superalloy, heat-resistant alloy and other difficult to machine materials of finishing, semi-finishing turning.

Insert coatingchart

The carbides with special crystal structure improves the red hardness of the insert matrix and enhances the high temperature resistance of the insert.

Wodenco offers coated inserts that provide 100% satisfaction in the industry, both domestic and overseas market. We have CVD coating, PVD coating, Black coateing, Multiple coating inserts and so on. Ultra fine coating, better wear resistance and toughness. The coating surface is polished and suitable for processing viscous materials.

For all types of dies, we can perform the regrinding service in short time and with significant cost savings for our customers.

CVD coating brand, good spalling resistance, (medium thickness Al2O3 + thick TiCN) coating is combined with hard substrate. It is suitable for medium and high speed turning of cast iron, and can withstand slight intermittent cutting at medium speed. This brand also has strong generality when it is applied to the milling of cast iron.

The combination of nc-TiAIN coating and tough cemented carbide matrix is suitable for cutting and grooving of all kinds of processed materials, realizing the perfect combination of safety and wear resistance.

Tools and Equipment Power Tool Accessories Router Accessories Router Cutter Inserts. 14mm Solid Carbide Insert Knife. Groover Knife Insert. Fastenal Sku ...

The ultra-fine TiAIN based nano-coating with wear-resistant and high-temperature resistant elements, provides effective protection for cutting edge with its high coating hardness and excellent high-temperature resistance. Its special coating treatment technology makes the coating and matrix more combined, suitable for finishing turning of stainless steel materials.

CVD coating brand, smooth surface and ultra-fine grains, (ultra-thick Al2O3, thick TiCN) coating combines with hard substrate. It shows excellent wear resistance in dry high speed cutting of gray cast iron.

Tungsten carbide parts offer a better alternative in the case of industrial parts subject to wear. These include knives and blades, moulds, punches, guides, ...

Kennametalturningcatalogue pdf

The coating surface is extremely smooth, with excellent anti-friction performance, reducing the occurrence of built-up tumor

The matrix with good toughness and strength combined with TiCN, thin Al2O3 and TiN coating is suitable for semi finishing and rough machining of stainless steel.

Image

******************************************************************************************************************************************************************************

CVD coating brand, good anti-stripping, (medium thickness Al2O3 + thick TiCN) coating is combined with hard substrate. It is suitable for medium and low speed wet milling of cast iron (such as nodular cast iron) with toughness requirements, and also suitable for turning under intermittent conditions.

2020114 — We can reduce the footprint of aluminium products is through dry machining. This means no longer using oil nor drinking water and lubricants in machining ...

Rolling Tools produces dies in conventional high-speed steels (AISI M2 and AISI M42) and special steels with heat and surface treatments developed according to the material to be rolled.

Rolling Tools manufactures flat thread rolling dies for screws and bolts, ogival, knurling, grooves andd based on customer design.

The excellent combination of high wear resistance matrix and MT-TiCN, thick Al2O3, TiN coating is suitable for finishing and semi-finishing of cast iron materials.

Image