Kudos for that! That’s actually some of the best experience you can get. Understanding the limitations & how wear can affect machine accuracy is key to becoming a well-rounded machinist. You will notice most well-used & ragged out mills will display more wear in the center of travel where most of the work has been done for years. You will learn (or have probably already learned) that the table brake lever is your friend when working in the ‘slop zone’.

You’re very welcome, and best of luck with the project. Yes, chip welding can be an issue (generally only without oil). Sometimes I attempt cutting without oil (for example, when my part is stuck to the work surface with 2-way tape). I just had a job this morning where this was the case, and I started getting chip weld. I was right there babysitting it, so I swapped in a new end mill and finished up the job. I will salvage the end mill later. I backed my DOC down to .030 with a feedrate of 20 ipm, but backed that down to 20% to start. With small parts stuck down with tape, you really have to be careful of pushing the limits of adhesion of the tape, lest the part should shift. I’d rather finish the part at a snail’s pace & not have to start over because of part shift.

Custom Tooling Request · A description of what you need your custom tool to do. · What Scotchman machine will it be used on. · A print, drawing, or photo ...

I am putting together a post with everything we did. I am just waiting to go back to school so I get some better pictures. In the meantime here is what we ran:

1X DOC isn’t an issue as long as your radial stepover and chip load are adjusted for. Just keep in mind that although the 1F machines are very rigid for what they are, they are still less rigid and contain much less mass than a proper VMC. Use an adaptive strategy with stock to leave and then clean it up with contour and/or horizontal tool paths.

I found this video to be very informative. Shapeoko Feeds & Speeds and Machining Tips! - YouTube 1x dia. DOC is only if your machine is built like a rock. Actually i think the 1F is strong enough, but if it’s a Makita router, that may put too much flex/vibration in the tool. Not saying it can’t be done but tool life may suffer severely. Mainly from not having a high enough feedrate to stop the cutter rubbing.

Like virtually all other CNC routers, the ultimate weak point (particularly when machining metals) is the Z axis. The Z axis sub-assembly is 2x removed from the solid base of the machine, meaning that any play in the X, Y, and Z axis is ultimately absorbed and manifests itself @ the tip of the cutting tool. Now there’s not much play or slop in the X & Y axis, but the Z is substantailly smaller and there is only 1.5" of tool holder hanging onto the router. In addition to this, take into consideration that the tip of the average tool is going to be about 4.5" - 5" below the centerline of the 1.5" router holder. All that adds up to a good bit of leverage working against you when machining metal. Chip-load calculations are great and I applaud ppl that put that much thought into the process. I personally don’t, mostly because I’m an old-school manual machinist and everything was done primarily by seat-of-the-pants feel & gut instinct. But back to chip load calculations & derived feeds & speeds: these calculations are based on ideal machine setup and rigidity. The calculated feedrate may work well for someone running a Onefinity or better, but Imagine our stock X-Carve brethren applying the same prescribed feedrates.

You mentioned the use of an adaptive strategy, what CAM software are you using? Our team is currently using Carbide Create (for CAM). Fusion360 is not an option, as our team (along with pretty much the rest of the FRC community), uses SolidWorks. Is CC sufficient for 2D aluminum? There is Solidworks CAM and I believe we get a MasterCAM license but I’m looking for something simple and easy to use, especially for new students.

Carbide3D designs and sells desktop CNC milling machines and accessories. This channel is dedicated to educating and inspiring those that are looking to purchase a machine or already own one.

The worst part of the cut was the fact that we used Carbide Create. It doesn’t ramp while plunging, putting a significant amount of stress on the cutter and sounds horrible.

May 13, 2024 — It's a unit of measurement for a concept in machining called Surface Speed or sometimes Cutting Speed. Of course there are also metric units ...

No need to be sorry, your advice has been super helpful! I’ll be completely honest; I only learned about feeds and speeds when I got into CNC last summer. I’m 17 years old and I have been using a manual mill since 13. A lot of our machining on our team is done by ear and seeing what our (rickety) machines in the shop can handle . That being said, our first cut with alu went really well. Knowing those cutter recommendations are for industrial machines, we backed it off quite a bit and got a flawless cut!

2024719 — 2024. 5. 16 - How To Get Nails Out Of Concrete. There are any references about How To Get Nails Out Of Concrete in here. you can look below.

In the first pic is a .25" 2 flute end mill on my 1F machinist model. Second pic is the chips from the cut. Hope this helps.

I have cut various woods using the standard calculations and have gotten pretty decent results. Can I do the same with aluminum?

Image

2024829 — Tools Required: CNC milling machine, end mills, and appropriate cutting fluids. Cut Titanium. 5. Brazing and Welding. While not strictly " ...

Image

That DOC does seem a bit much for aluminum, although I haven’t had any experience with using 1 flute end mills. When I do aluminum, I usually do .060 DOC with feedrate of 30ipm (4-flute end mill), but I usually back down the feedrate by 50% until I get a feel of how it’s going to do. It also depends largely on my setup, and if I’m running cutting oil or not. Then bump up the feedrate as I see fit. But I’m usually doing paid jobs where the overall tolerance must be +/- .005, so my main priority is making sure I get a good quality cut. I’m not running production, so I’m not in a hurry. Just enjoying the project.

Drill Length Type, Stub ; Hole Tolerance, h8 ; Cutting Direction, Right ; Through Spindle Coolant, No ; Weight, 0.1 lbs \ 0.1 kg.

I have a few questions about milling aluminum. I have done the basic math regarding feeds and speeds… Theoretically, I’m all good but I have never cut aluminum before and I don’t really know the limitations of the machine (set it up a few weeks ago).

Thanks so much for your advice! I am part of an FRC robotics team and also need parts to be within 0.005in and churned out pretty quickly, obviously not prioritizing quality over time… I think I will start out with a DOC similar to what you use and work my way up. Do you get a lot of chip welding with the 4 flutes, even with cutting oil?

2012823 — A triple start is a good improvement when putting a cap on a pen. If you thread your parts so that it takes one full turn to secure the cap to the body, then ...

Micromachining. We are carrying out various micromachining projects using both mechanical machine tools and ultrashort pulsed lasers. ... Various micro features ...

Sorry, I should have been more clear, we do use Solidworks for design/modelling but Carbide Create for CAM (not design). Regardless, you have been super helpful, I really appreciate your (and everybody elses’) comments!

2024317 — Request PDF | Work Hardening Behavior of Aluminum over a Wide Range of Strain | The work hardening behavior of high purity (4N) aluminum was ...

Referencing this datasheet for my cutter, do the above parameters seem reasonable? Is there anything I should change? I am currently using carbide create.

No problem, always glad to help. I use Fusion 360 for both CAD and CAM. Yeah if you are looking to keep tight tolerances and cut quality I’d look into Fusion or make the jump to solidworks and Master Cam. Both Fusion and Solidworks are substantially more powerful than Carbide create. Not that it won’t do the job or to bash it or anything as it is good for the market it was designed for and is a great primer for new students. There is a point though where moving into a more powerful software suite will take your design and programming to the next level. And incorporating the engineering aspects of the software packages like creating movable joints, stress/load analysis and mass allocation could be a big advantage for your team.

Thanks! No, this is some sort of part I made for an Xometry customer, not entirely sure what it is. But this is very typical of the parts I take on for them, mostly just 2D profile parts in thin aluminum or other plastic-type materials.

If you are machining Aluminum (Aluminium) using Carbide Create then I would look up Winston Moy on The following Youtube Channel as he has done a few decent videos on the subject. Albeit he is using the Shapeoko/Nomad machines which they sell.

2019116 — Yeah it provides a good bevel. The blades are costly though, but you can flip the blade to the other side once it starts to wear out. I sharpen ...

IP Okokpujie · 2019 · 53 — Abstract. This review paper focus on the application of various machining techniques based on the phenomena of CNC operations, the study of different machining ...

We only did a contour/2D cut, so I haven’t yet played around with the stepover. In our second cut we bumped up the DOC to 0.030" and it seemed to handle. We are aiming for at least 0.050", but like many people said, start low and work your way up!

Great thread! Would love to know what specs you used for that flawless cut! I planning on machining aluminum for the first time also and this thread has been super helpful!!!

I have been using a manual mill since 13. A lot of our machining on our team is done by ear and seeing what our (rickety) machines in the shop can handle .

Thanks for the reply. As of right now, I am only doing super simple 2D work (outer/inner contours), mainly gussets and gearbox plates for our FRC robot (student competition).

17mm wrench for scale. Ignore the little dent near the bottom, that was me trying to remove the tabs We sanded the part with some 120, filed the edges and voila! Finished_Product1920×2575 438 KB