The O-Shot® procedure helps a woman bridge the gap between sexual dysfunction and having a more pleasurable and enhanced sexual experience.

Using your fingers, a sex toy or with the help of your sexual partner’s penis, try to reach farther into the vagina. When the penetration is no longer possible or if the region within the vagina is harder, then you would have encountered the cervix. Now, explore the underside region (towards your back) by applying varying amounts of pressure, rubbing, stroking or mild poking until you find the spot that is most pleasurable. This is the O-Spot.

We recommend these bits be used in a variable speed router set to a maximum of 18,000 rpm and are ideally suited for use in your router table.

O-Shot® is a quick, non-surgical and relatively painless clinical procedure invented by Dr. Charles Runels that has an undeniably great potential to improve the sex life of all women.

As you now know, from the above topic, where the O-Spot is located, finding the region is not all that difficult with a little self-experimentation.

If you've ever assembled a project, like a chest of drawers or a table, and forgotten to roundover the bottom edge of the top, these bits can be a life-saver. (Don't ask me how I know this.) Just use the bit in your hand-held router to finish off that bottom edge. This is just one of the many uses I've found for these bits that prevented me from having to tear down the project to finish routing the edge.

These versatile router bits allow you to simultaneously put a radius on the top and bottom edges of your workpiece. Using the included shims and bearings, each router bit allows you to cut stock up to 1-5/8" thick for roundovers and 1-7/8" thick for bead profiles. Remove the shims to rout a half-round bullnose or bead profile in one pass. Each bit includes a bearing for routing roundovers and a smaller bearing for routing bead profiles.

Unlike a traditional bullnose bit, these woodworking router bits can be expanded from a full half-round bullnose profile all the way out to rounding over both top and bottom edges of a workpiece up to 1-5/8" thick. If you want to create a bead profile on both edges at once, you can work with stock up to 1-7/8" thick.

The double roundover bits come in your choice of 3 different radii: 1/8", 1/4", and 3/8"-radius. The best part is, all three bits are available in a money-saving set (Item 00-390).

The above-mentioned points differ from one individual to another. Please consult with your gynaecologist before proceeding.

The O-Spot is located farther within the vagina, near the cervix along the underside, i.e. towards the lower back, wall of the vagina. Since the O-Spot is located deeper inside the vagina, most women and their sexual partners are often unable to access the spot that can potentially make the act of intercourse much more pleasurable.

You can combine the 3/8" and 1/4"-radius cutters to create a very traditional and attractive thumbnail edge detail on a tabletop or chest-on-chest. This is a common profile on Shaker-style and other types of furniture.

By submitting this form, you agree to receive recurring automated promotional and personalized marketing messages (e.g. cart reminders) from Infinity Tools at the email provided when signing up. Consent is not a condition of any purchase. Email frequency varies. View Terms  & Privacy.

The O-Shot® is a clever technique to use the body’s own regenerative ability to create new tissue. A small amount of blood is first taken from the patient into a tube and is then put inside a centrifuge. The centrifuge helps to separate the platelet-rich plasma (PRP) from the blood. This PRP (containing call regenerative growth factors) is then carefully injected into specific areas of the vagina which trigger stem cells to increase blood flow and generate healthy tissue growth as well as help improve the vascularization of the area.

Each of these bits comes with two bearings so that they can be used to make roundovers, beads with up to a 1/8" fillet, and full beads with 1/8" fillets on both faces. Remove the bearing to make a true bullnose profile or a full bead. With these options for customization, each of these bits can act like several router bits in one.

These bits can be customized to rout profiles based on the thickness of the workpiece.  You can add or subtract shims to fine-tune the spacing between the cutters by as little as .003" at a time. The order of the shims isn't important as long as the bearing spins freely and the distance between the top and bottom cutter are correct for your project.

The O-Shot® is not limited to any specific age group of women. It can be performed on any sexually active woman and the entire procedure typically takes only about 30 minutes from start to finish.

It is important to keep in mind that, just like the G-Spot, the O-Spot is not a distinct anatomical part of the human vagina, but a region deep inside the vagina.

Women can choose to get the procedure any number of times at varying intervals. The effect of the procedure, in rare cases, can last a lifetime but they generally last about 12 to 14 months.

If you want to make a decorative bead for something like the front edge of a bookcase shelf, choose the 1/4"-radius bit and set it up to make a bullnose profile, as shown below. Rout the edge on a wide piece of stock, to create a 1/2" bead with a 1/8" fillet along the top and bottom, and then rip the edge free at the table saw.

The patient can resume their regular life soon after the procedure. The effects of the procedure can be seen in as soon as 1 day in rare cases but the typical time period is about 3 weeks.

On average, women repeat the procedure once every year but can even be repeated every 6 months or every two months. However, to see the full effects of the first treatment, a period of 8 weeks is recommended before repeating the procedure.

The perks of urinary are not just limited to better orgasms but also have other amazing effects such as increased sex drive, vaginal rejuvenation, help with sexual dysfunction and more!

Infinity Tools Double Roundover and Beading router bits are very versatile and allow you to simultaneously put a radius on the top and bottom edges of your workpiece. Using the included shims and bearings, each router bit allows you to cut stock up to 1-5/8" thick for roundovers and 1-7/8" thick for bead profiles. Remove the shims to rout a half-round bullnose or bead profile in one pass. Each bit includes a bearing for routing roundovers and a smaller bearing for routing bead profiles.

Another reason to have the 3-piece bit set is so you can mix and match cutters to create a different radius on the top and bottom edges in a single pass.

The O-Spot (short for “Orgasm Spot”) is another highly sensitive and erogenous region deep within a woman’s vagina that is capable of providing the woman with satisfying orgasms when sexually stimulated.

O-Shot® is nearly a painless, minimally invasive and quick procedure without any adverse side-effects. The major risks are slight bleeding, swelling and irritation that generally subside within few hours.

There are a lot of situations where being able to round over both the top and the bottom of a workpiece can be extremely convenient and save a lot of time. Let's say you just finished making a stack of kitchen cutting boards for gifts and are now tasked with rounding over all the edges of each of the cutting boards. You could use a standard roundover bit and round over one face then flip the board over and round the other. But you can save time by using the Infinity double roundover and beading bits to rout both sides at once, cutting the work in half.

Just like the G-Spot, there are other erogenous spots in the human vagina which when stimulated can lead to intense explosions of orgasms.