Match drillingaerospace

After a successful drill out (#2 of the day), I finished setting the rest of the spar reinforcements and snapped these two pictures.

First thing in the morning, I had to run some errands, one of which included a stop by Harbor Freight to exchange my Automatic Compressor Drain Kit that had a crack in it. While I was there, I used two coupons. One, for a free tape measure, the other for almost half off a 6″ digital caliper. Walked out the door with a new caliper, tape measure, and an exchanged drain kit for $10. Can’t beat that.

After match rilling both skins and finishing the HS-710/HS-714 to HS-702 holes, The skeletons lay ready to disassemble, deburr, dimple, edge finish, surface prep, and prime.

First thing after breakfast, I snagged the two VS spars and the spar reinforcement and headed into the kitchen to finish some surface prep. After about an hour, I had all three pieces scuffed up, cleaned, and back outside. Here is a shot during scuffing. You can see the top half has been scotchbrited and the bottom half is the raw part after removing the blue vinyl.

Elsa Thompson Brandon Walston, known by his stage name Granddaddy Harvey, is a rising artist with a passion for creating music that resonates ...

I went ahead and scotchbrited all the HS ribs. I was sick of the aluminum dust on my hands during scotchbriting, so I took these inside and did them with warm water (only reason for warm was so my hands didn’t get cold) in the kitchen sink. Worked well with a lot less dust. (Also, I think showing pictures of my work with finished pieces looks a lot better than the original parts, which are all shiny and finger-printy after my grubby hands work with them.)

Rudder counterbalance matchrilled to the counterbalance rib. Also, there's the hardware that will be used to fasten these two together.

Then, I used the previously marked and pilot drilled holes in HS-405 to drill forward through the HS-702 (front spar) and HS-710/714 (reinforcement angles). The 12″ bit really came in handy here.

Match drillingholes

Surface Speed: (sfm) (See tables below). Spindle Speed, (RPM). Spindle Speed, (RPM). Feed/Tooth, (Tooth Load). Number of Teeth. Feed Rate. Milling Speeds (HSS ...

Carbide. Sumitomo. Electric. Kyocera. Dijet. Sandvik. Kennametal. Seco Tools. Iscar. TaeguTec. Ingersoll. Widia. Walter. Ceratizit. •PCBN and PCD for Turning.

The new hole is on the bottom right. After countersinking, I used a rivet and my flush set to dimple the rib. Not perfect, but it'll work.

They didn’t have any maroon on the shelf, but they had some grey. I asked the guy out front, and he went to the back and grabbed 3 unpackaged pieces. Usually, there are $5 or $6 for the three. He gave them to me for a couple dollars, which was nice.

Then I mocked up the R-405PD Rudder Horn, R-710 Horn Brace, R-917 Shim, R-902 Spar, and R-904 Bottom Rib. Some people need to use blind rivets in some of these holes, but I figured I could do it with all solid rivets.

Whether you're working with magnetic soft steel, structural steel, alloy steel, or even thermoplastics and synthetic materials, Erix chamfering tools deliver ...

I followed Mike Bullock’s advice and clamped the rear spar to a couple of 2x4s. This let me matchdrill the rear spar vertically, which helps a lot with getting a perfectly straight hole.

I didn't forget the hole on the bottom of the picture. This hole is match-drilled with the rudder tip and then dimpled to #30.

And after much consternation (including using my double offset set as a bucking bar), I got the two outside rivets bucked.

Leave a Comment » | Empennage | Tagged: cleco, HS, Match-drilling, Ribs, skeleton, skin, spar | Permalink Posted by Andrew

Shop Alemite 54730 at Applied.com, which includes; Straight Type,1/8 NPTF x 1/8 NPTF,For Handling Grease Controls Valves,Prevents Damage to Hose From ...

Anyway, after the birthday festivities (a.k.a. Jack and Ginger inhaling their biscuits), I managed a couple hours on the project. Here, I clamped HS-404 in place after having first marked holes and drilled #40 pilot holes in the aft flange. The instructions have you mark and drill pilot holes in the HS-405, but why drill from aft to forward, hoping you don’t run into edge distance problems when you could drill from forward to aft? For the outboard holes, I did use the HS-405 for pilot holes. You’ll see.

Then, on to real work…kind of. The manual wants me to attach the hinge reinforcing plates to the spar, then move to the outer ribs.

Then, I cleaned off the hinge brackets, got them clecoed to the rear spar, and clecoed the rear spar to the front spar and ribs.

Leave a Comment » | Empennage | Tagged: Buck, Deburring, Devinyl, Dimpling, Empennage, Match-drilling, Priming, Ribs, Riveting, Rudder, Scotchbrite, scuff, shoot, skeleton, skin, spar, Vinyl | Permalink Posted by Andrew

I had a very specific order here. First, deburr, scuff, dimple and prime the top, forward edge, and bottom edge. Then, while the primer is drying, devinyl the aft edge (vinyl used as masking for the primer), deburr, scuff and dimple the aft edge. This edge doesn’t get primed, as we’ll use the fuel tank sealing instructions with Pro-seal to glue the trailing edges together.

While I waited for the Goo Gone to do its magic, I decided to start clecoing the front spar and ribs together. You can also see the rear spar and rear spar reinforcement in the upper left corner of this picture.

Match drillingtools

Then, I spent a couple minutes making the slot at the bottom of the skin a little bigger. One of the flanges from the control horn fits in here, and during initial assembly, there was some interference.

Then, I matchdrilled the rest of the HS-404, which had been clamped in place in the above pictures. After that, I finished match-drilling the rest of the skin for the right side. After you finish and pull the skin off, you can drill the remaining HS-702 holes using the HS-710 and HS-714 angles as guides. Here are the last six holes drilled after pulling off the skin.

Then I inserted the HS-404 (front inboard) and HS-405 (rear inboard) ribs and clamp. Here, you can see the HS-405 clamped.

Leave a Comment » | Empennage | Tagged: cleco, Empennage, fluting, Front spar, Match-drilling, Rear spar, Ribs, Scotchbrite, scuff, skeleton, skin, spar, VS | Permalink Posted by Andrew

It was Jack’s birthday today (he turned 3), so I ran out to Chik-Fil-A to get him is once a year human food treat. A chicken biscuit. Of course, Ginger needed one too (“so she doesn’t feel left out”) and so on, which meant my girlfriend and I also got biscuits. Here are Jack and Ginger.

I had some trouble with dimpling the last three holes in the rudder bottom rib. I drilled and countersunk a hole in a spare piece of steel I had, then realized it was too far from the edge to work. Awesome. Here’s a shot of my second attempt.

Blah blah blah, assemble the skeleton. For now, I didn’t do any match-drilling. I do that hole-by-hole as I take the thing apart.

I went ahead and match-drilled it. I’ll examine the edge distance a little more closely when I take apart the HS for prep. I repeated all the steps for the right side, then started in on match-drilling the skin to forward spar holes inboard of the 707. (Below, you are looking at the bottom of the stab, so the right HS is on the left in the picture. you can see the extra clecos from what I will call the “middle ribs” (708 and 707) inboard along the front spar. Those are not pre-punched on the spar, so you have to use the holes in the skin to match-drill.)

Example of brand new cleco on the left, and two used clecos in the middle. Eh, they work just fine, they're just not as pretty.

I did the right side too (mostly so I could take the next picture), then match-drilled all of the rib/spar attach points to #30, (except for 708/603), which they have you do later to a #21.

1) Fix rivets in right elevator 2) Trim right elevator weight 3) Clean up HS cuts 4) Look for underdriven rivets 5) REBUILD RUDDER :-( 6) Finish riveting right rear spar 7) Replace rivet on inboard rear spar edge 8) Start on left wing 9) FB tips on emp 10) Wingtips

Then, time to matchdrill the skin to the spars and ribs. Same process here. Cleco every other hole, drill, mark dots, move clecos, repeat.

Use it to remove excess p-tex from base repairs prior to using a metal scraper. The Surform will remove the bulk of material greatly reducing the amount of ...

Jack and Ginger (Jack's on the right) on the beach last summer. Happy Birthday Jack. You're 3 now. Start acting like it.

20 rivets set so far. Then I moved on to the R-606PP Reinforcement plate to R-902 Spar to R-917 Shim to R-405PD Rudder horn rivets. These need to be AN470AD4-7 rivets, which are LONG. I did have to drill one of them out. That’s #3 for the day. Boo.

This happened because I was bucking from above and shooting from below. The gun jumped around cause I was supporting it’s weight instead of letting gravity help me. That’s a no-no.

Yeti Tool Ltd provide affordable solutions for portable precision cutting on-site and in the workshop. Introduce CNC routing to your tool box with ...

In addition to the items they want you to do to both at the same time (roll leading edges, install rod-end bearings, etc.), I’ll have to come back to do three things on the right elevator:

Match drillingkit

I broke out the cordless drill (quieter than the air drill) and finished matchdrilling the right side of the vertical stabilizer.

Leave a Comment » | Empennage | Tagged: cleco, Construction Manual, Drilling, Front spar, Ginger, Jack, Match-drilling, Rear spar, skin, spar | Permalink Posted by Andrew

I've been coming to Mina for my eyebrow threading since 2008. Now she has opened ...

I started clecoing the rear spar doubler to the rear spar, and then realized they want you to put the hinge brackets in now. I quickly located VS-410PP, VS-411PP, and VS-412PP, and got the Goo Gone out to help pull these stickers off.

While I was moving everything around getting it ready for riveting, I broke my first tool. Now, it was about $0.50 from Harbor Freight, but I was still upset.

Finally, I found one more of the stiffener angles. I got that devinyled and then cut from hole to hole to form some of the smaller stiffeners.

Next, I slid the flange of the bottom rib under the rudder horn and lined up the holes. Now I need to drop some rivets in here.

Then you get to cleco on the skin (wuhoo!). I had trouble with HS-707 here. the very tip of the rib kind of caught on the  skin (vinyl); I had to really work to get it back into position and clecoed. you can see here I clecoed every hole on the HS-707.

I figured out that if I take off the R-904 bottom rib, I can reach in from above (bottom right of the picture) and get the horn brace to rudder horn rivets here, then slide the forward flange of the bottom rib under the rudder horn and get those from the lightening hole. Here I am setting the horn brace to rudder horn rivets.

RIP cheap plastic clamp. (I'm lying. I actually gut the orange part off the other side and threw the clamp into a box somewhere. I'm sure it will come in handy at some point, even if it doesn't have the orange pads.)

Well, it’s monday. And even though I have a couple things remaining on the right elevator, I am going to follow the flow of the directions and move on to the left elevator before coming back to finish both of them.

Match drillingmachine

Same routine. Drill every other hole, mark with a dry-erase marker, move clecos, drill remaining holes. Because the root forward rib gave me a little trouble when clecoing during initial assembly, I had 100% clecoed it. For this area, I removed one cleco, matchdrilled, then replaced the cleco. I just didn’t want it to move around on me at all.

Leave a Comment » | Empennage | Tagged: counterbalance, Devinyl, doggie-treat, fluted, Ginger, hinge reinforcing plates, install rod-end bearings, Jack, left elevator, Match-drilling, Ribs, right elevator, rivets, roll leading edges, RTV, skeleton, spar, Stiffener, trailing edges, trim spar, trim tab | Permalink Posted by Andrew

As I only have about a half an hour tonight, my plan was to just cover the basics. First, lay out all of the left elevator parts.

Here’s my process. Cleco every other hole, match drill, mark the drilled hole with a dry-erase dot, move the clecos, repeat. Here, you can see my dots.

Apr 19, 2023 — CNC milling aluminum speed can typically range from 400 to 1200 SFM (Surface Feet per Minute), depending on the type of aluminum alloy and the tool being used.

In between some yardwork, watching the sprinklers, and cleaning up the house, I made some good progress on the airplane.

Leave a Comment » | Empennage | Tagged: drill bit, Empennage, Ginger, Jack, Match-drilling, skeleton, skin, spar, VS | Permalink Posted by Andrew

Then used the #40 pilot holes I made in HS-405 to drill through HS-702 and HS-710 (or HS 714 for the other side). Here, you can see the 12" bit really showing its stuff.

Nickel-containing materials are now being widely used to meet the demanding conditions of the oil and gas industries and power generation, including renewable ...

After finishing up the ones you can reach from the aft side of the rear spar, I flipped the whole assembly over and match-drilled the two remaining holes (that aren’t drilled in the upper half of the lower set of hinge brackets).

Here, you can see that I am in the middle of moving clecos. The one in the center of the picture gets moved one left (into the marked, already drilled hole), then the one to the left of that gets moved one left, and so on.

Then I match-drilled the HS-405 to the HS-601PP (skin). I didn’t do the top or bottom forward most hole, because I seem to be having edge distance troubles on the HS-405 and HS-702 spar. I checked everything and it seems to be right. I checked some other build sites to see if other people have run into this, no one mentioned it. Right as I was going to post a question on the VAF forums about this, a new thread popped up. Apparently this is a common problem, and the edge distance on HS-405 is not to be worried about. It’s a little confusing, though, given the prepunched nature of the parts.