I ground three flat spots onto the other end of the threaded rod to make it easier to grab it in a drill chuck. Again, I used two-nuts as a visual guide to help me space the three flat spots evenly.

taps are usedto make threads in.

I then used my jig to clamp the threaded rod in the vise. The jig itself serves as a guide for a cut-off disk in an angle grinder to cut the slots in the threaded rod.

How to makeexternalthreads

Use the shortest drill possible as shorter drill bits are more accurate and because they’re more rigid they don’t break as often, Shorter drill bits are also better in confined spaces.

I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out.

I cut a total of six slots in the threaded rod. I used two hex nuts jammed against each other on the threaded rod to guide how much to turn it by to space the slots. Spacing four slots evenly would have been more tricky unless I found a square nut to fit on the threaded rod (or I suppose, I could have jammed a square piece of wood between the two nuts as a guide)

How to makenewthreads ina hole

The metal one works just fine in wood (and metal). Interestingly, the metal tap is slightly bigger than the one I made. When threading holes in metal, the hole needs to be slightly bigger than the bolt or threaded rod that screws into it, or it will get stuck. With wood, having a hole slightly smaller is not a problem because the wood has some flexibility. That's how wood screws engage. The homemade tap cuts the thread with just the first few turns so it can cut threads closer to the bottom of a blind hole. I could just make another one with no taper at all to cut threads all the way to the bottom of a hole. That's the nice thing about homemade tools — infinitely customizable. Testing it out. Worked well. Though, in retrospect, I should have cut the flutes slightly larger because they had a tendency to get filled with sawdust. Drilling a larger hole before tapping would also help. It was easy to screw a threaded rod into the resulting hole just by turning it with my fingers. Then trying the same method with a wood bolt, which has much coarser threads. I cut wider flutes in this one so I didn't have to back it out half-way to clear the chips. I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out. I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

118º Standard is found on most common drill types. 135º Self-centering (split point) enables faster starting and cutting actions, especially in hard steels and stainless steel.

How tothreadmetalrod

But before cutting slots in the threaded rod, I cut a slight taper in the end of it. That way the thread will be cut over the course of several turns instead of just by the very tip.

Tapping thread chart

- For hard to machine materials, interrupted cutting or unstable setups a reduction of feeds and speed of 50% may be required.

I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

The homemade tap cuts the thread with just the first few turns so it can cut threads closer to the bottom of a blind hole. I could just make another one with no taper at all to cut threads all the way to the bottom of a hole. That's the nice thing about homemade tools — infinitely customizable.

I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

Dills are often described by their length, referring to the effective flute length or maximum drilling depth in relation to the diameter.

How totapthreads in metal

- When drilling using Hand held Drill machines, Rpm may need to be reduced as feeds are being applied manually. This may help prevent excessive wear and work hardening of materials.

re-tappingthreads

Testing it out. Worked well. Though, in retrospect, I should have cut the flutes slightly larger because they had a tendency to get filled with sawdust. Drilling a larger hole before tapping would also help. It was easy to screw a threaded rod into the resulting hole just by turning it with my fingers. Then trying the same method with a wood bolt, which has much coarser threads. I cut wider flutes in this one so I didn't have to back it out half-way to clear the chips. I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out. I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

I cut wider flutes in this one so I didn't have to back it out half-way to clear the chips. I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out. I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

Parabolic Design (often called deep hole jobbers) – usually 40° Helix angles, the open design helps chip removal out of the hole. These are especially effective in very soft materials like plastics and aluminium’s.

How to make threads in metalpipe

I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024)

Home made thread tap next to a proper metal thread tap. The metal one works just fine in wood (and metal). Interestingly, the metal tap is slightly bigger than the one I made. When threading holes in metal, the hole needs to be slightly bigger than the bolt or threaded rod that screws into it, or it will get stuck. With wood, having a hole slightly smaller is not a problem because the wood has some flexibility. That's how wood screws engage. The homemade tap cuts the thread with just the first few turns so it can cut threads closer to the bottom of a blind hole. I could just make another one with no taper at all to cut threads all the way to the bottom of a hole. That's the nice thing about homemade tools — infinitely customizable. Testing it out. Worked well. Though, in retrospect, I should have cut the flutes slightly larger because they had a tendency to get filled with sawdust. Drilling a larger hole before tapping would also help. It was easy to screw a threaded rod into the resulting hole just by turning it with my fingers. Then trying the same method with a wood bolt, which has much coarser threads. I cut wider flutes in this one so I didn't have to back it out half-way to clear the chips. I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out. I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

You can use metal thread taps for wood just fine, but I wanted to experiment with making my own from a piece of threaded rod. I started by making a "jig" to hold the threaded rod for grinding slots in it. But before cutting slots in the threaded rod, I cut a slight taper in the end of it. That way the thread will be cut over the course of several turns instead of just by the very tip. I then used my jig to clamp the threaded rod in the vise. The jig itself serves as a guide for a cut-off disk in an angle grinder to cut the slots in the threaded rod. I cut a total of six slots in the threaded rod. I used two hex nuts jammed against each other on the threaded rod to guide how much to turn it by to space the slots. Spacing four slots evenly would have been more tricky unless I found a square nut to fit on the threaded rod (or I suppose, I could have jammed a square piece of wood between the two nuts as a guide) I ground three flat spots onto the other end of the threaded rod to make it easier to grab it in a drill chuck. Again, I used two-nuts as a visual guide to help me space the three flat spots evenly. Home made thread tap next to a proper metal thread tap. The metal one works just fine in wood (and metal). Interestingly, the metal tap is slightly bigger than the one I made. When threading holes in metal, the hole needs to be slightly bigger than the bolt or threaded rod that screws into it, or it will get stuck. With wood, having a hole slightly smaller is not a problem because the wood has some flexibility. That's how wood screws engage. The homemade tap cuts the thread with just the first few turns so it can cut threads closer to the bottom of a blind hole. I could just make another one with no taper at all to cut threads all the way to the bottom of a hole. That's the nice thing about homemade tools — infinitely customizable. Testing it out. Worked well. Though, in retrospect, I should have cut the flutes slightly larger because they had a tendency to get filled with sawdust. Drilling a larger hole before tapping would also help. It was easy to screw a threaded rod into the resulting hole just by turning it with my fingers. Then trying the same method with a wood bolt, which has much coarser threads. I cut wider flutes in this one so I didn't have to back it out half-way to clear the chips. I figure this could be a handy alternative to using a machine screw and threaded insert for some adjustment knob or fastening knob on a homemade machine. With so much wood between the threads, it's very unlikely that the threads would wear out. I did a quick wear test, screwing the screw in and out many times while pushing hard against the drill. Then I had the idea of setting it up to use the screw to lift my table saw. Again, up and down many times, no sign of wear. I figure these coarse threads could be handy for something where a cover needs to be held in place. If I make wooden knobs for the wood bolts, that will make for a cheap and easy way to make threaded knobs to hold a cover onto something. I am using a piece of oak here. Soft woods like pine or spruce would not hold up as well. See also: I bought the improved Jimmy Diresta ice pick.... 20 years ago! (2021) Making bandsaw blade guides (2016) Making wooden hinges (2013) Basement bookcase (2017) Dad's wooden doorlatches (2007) Making a German chip carving knife (2015) Angle grinder flatcut-off jig (2016) Grinding a machine taper with an angle grinder (2016) Cut any thread pitch on the metal lathe (2024) Back to my Woodworking website.

For example: Jobber drill length drills are 5xD, this means a 5mm jobber drill would have an effective drilling depth of 25mm.

Reduced Shank: 5XD (However, usually share a common length of roughly 6" (152mm) overall length with a 3-3/8" (86mm) flute length)