You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

... turning insert with High-Quality, Leading WNMG080408 Carbide turning insert Manufacturers & Suppliers, find WNMG080408 Carbide turning insert Factory Exporter.

How to hammernail into concretewall without drill

xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Jan 23, 2023 — Proline is called "alpha-helix breaker" because of its branch-side chain, which interferes with the backbone of the preceding turn.

How to put anailin a brick wall without a drill

Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Fluted Masonry Nails

Deck Screws vs Nails - Which is Better?Nail Guns - Drive Many Nails FastFree & Fast BidsCLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Related LinksDeck Screws vs Nails - Which is Better?Nail Guns - Drive Many Nails FastFree & Fast BidsCLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Quick Change Tool Holders · KBC #1 BXA QC TURNING & FACING HOLDER · KBC #1 CXA QC TURNING & FACING HOLDER · ALORIS #1 BXA QC TURN & FACE TOOL HOLDER · KBC #2 ...

Masonry Nails

Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Your email address will not be published. Required fields are marked *Comment * Name * Email * Website Sign up to my newsletter to receive expert advice for your home! Δ

Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

How to use masonry nails

Learn all about the benefits, the most popular alloys, the best finishes, and more to ensure your next project succeeds.

For nail making, iron ore was heated with carbon to form a dense spongy mass of metal which was then fashioned into the shape of square rods and left to cool.

IMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Masonry Nails forconcrete

The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Manufacturer's Grade H13A. ISO Number RNMG 19 06 00-SM H13A. Chip Breaker SM. Insert Style RNMG. Insert Size 64. Insert Hand Neutral. Coating Uncoated.

Advantages at a glance. · Face milling machine for large aluminum precision plates · Ergonomic loading · Surface quality < 0.4 µm · Milling tool up to Ø 3,100 mm ...

Free & Fast BidsCLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Concrete nails can be just regular 16d sinker nails. Two side-by-side will fit tight in a 1/4-inch-diameter hole in the concrete. Copyright 2018 Tim Carter

CLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Concrete nailgun

Can you nail into concreteslab

Nail Guns - Drive Many Nails FastFree & Fast BidsCLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Jan 2, 2014 — The title clearly states: Differences in drill angle depths. It says nothing about the differences in tip geometries. All it is about is the ...

"Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they..."Related LinksDeck Screws vs Nails - Which is Better?Nail Guns - Drive Many Nails FastFree & Fast BidsCLICK HERE to get FREE & FAST BIDS from carpenters who can drive nails into concrete.Concrete Nails Can Be Regular 16d Sinker NailsIMPORTANT NOTE: What you see in the video using regular nails should only be done when you know the wood will NEVER GET WET. If you use this method outdoors with treated lumber, then you MUST USE stainless-steel nails or double-dipped hot galvanized nails. You'll have to upsize the drilled hole to 5/16ths or 3/8th inches. Experiment until you have moderate resistance hammering in the nails.You can use regular 16d sinker nails as concrete nails in an upcoming project where you need to attach a piece of treated lumber to a poured concrete slab or a wall. The wood could be a 2 x 4 bottom plate for a wall or a simple 2 x 2 cleat for some utility shelving in your basement or garage.I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

I remember my dad drilling a large hole into dense concrete to install lead anchors to achieve this goal. It took hours and hours. Fortunately, I discovered my own way using regular 16 penny coated sinker nails and a hammer drill to permanently attach wood to concrete faster than you can say Jiminy Cricket. I can drill ten holes and install the nails in less than 15 minutes!xPlease enable JavaScriptAttach Wood to Concrete ShareWatch onAttach Wood to ConcreteDegree of Difficulty: What Tools and Nails Do You Need?You’ll just need a one-pound box of 16d coated sinker nails, a 20-ounce hammer, and a roto-hammer drill equipped with a 1/4-inch carbide-tipped bit that can drill a hole 6 inches deep.Should the Wood Be Treated Using Concrete Nails?Be sure the wood you’re using is treated lumber. It’s always a good idea to use treated lumber for any wood in contact with poured concrete.Concrete can become damp from contact with soil causing regular lumber to rot. Wood-destroying insects like carpenter ants and termites are often found near poured concrete that’s touching wet or damp soil. These insects do not like to eat treated lumber.Where Should I Position the Wood?Position the wood exactly where you want it to be when contacting the poured concrete. If it’s a bottom plate for a wall, gravity will hold it in place for you. If it’s a cleat for wall shelving, you may want to enlist a helper to hold the wood tight against the wall as you operate the drill.Should the Drill Be in Hammer Mode?Turn on the drill making sure it’s in the hammer mode. Hammer drills are amazing tools that use a rapid back and forth hammer motions while the drill is also rotating. The hammer blasts pulverized poured concrete and drilling is very easy.xPlease enable JavaScriptMilwaukee 2416 22XC Cordless Hammer Drill ShareWatch onMilwaukee 2416 22XC Cordless Hammer DrillWill the Hammer Drill Penetrate the Wood Plate?The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

With over 6 Performance Tool diagnostic tools in our assortment, finding the right products for your vehicle has never been easier.

The hammer drill will easily penetrate the wood. You don’t need to pre-drill a hole in the wood with a wood bit before using the carbide masonry bit. Just drill into the wood with the carbide bit.Should the Drill Be Pulled From the Hole While Drilling?Once the bit starts to bite into the poured concrete creating dust, extract the bit from the concrete and wood about every five seconds as you drill. This helps pull up to the surface much of the concrete dust and particles creating less friction on the sides of the drill bit. Apply even pressure on the drill as you drill down.How Deep Should I Drill Into the Concrete?Continue drilling until the hole in the poured concrete is at least two and one-half inches deep. If you’re drilling through 2x material this means four inches of the six-inch-long drill bit must be buried in the wood and concrete. (1.5 + 2.5 = 4 inches)How Many 16d Sinker Nails Should I Use?Take two of the 16d coated sinker nails and hold them together so the heads of the nails are even. Tap both nail heads at the same time lightly until they come in contact with the poured concrete.Continue striking the nails with the hammer with heavier blows making sure the hammerhead strikes the nails squarely in the center of the hammerhead. Short strong hammer strokes are better than wild large strokes that can bend the nails.How Well Do the Two Nails Hold in the Concrete?The combined diameter of the two 16d sinker nails is perfect to produce a very strong bite into the concrete. If you do this right and the concrete is strong, you often need a crowbar to extract the nails at a later date.Column HT021SummaryArticle NameConcrete Nails Can Be Normal Sinker NailsDescriptionRegular 16d sinker nails can be used as concrete nails. Drive two of them side-by-side into the right-sized hole in concrete.AuthorTim CarterPublisher NameAsktheBuilder.comPublisher Logo

Subscribe to the FREE Ask the Builder newsletter to receive professional advice for your home. Complete the form below and each week you'll get:DIY TipsTool ReviewsProject GuidesProduct Discounts, Giveaways & more. Unsubscribe at any time. We respect your email privacy.

The following are trademarks for one or more DEWALT power tools, accessories, anchors and concrete adhesives: The yellow and black color scheme; the D-shaped ...