End mill Bits near me

The 1/4" roughing endmill bit (hogging bit) is the bit when you need to remove massive amounts of material at one time from your CNC router project before you do your finish cuts.

The bit is pretty impressive with how much material it remove at once. But I am actually more impressed with Garrett than I am the bit! When I first got the bit, I had it for about a week or so, and then I made a mistake in my cut and the bit broke. Trust me, ANY bit would have broken in this case. But Garrett sent me a new one expeditiously…with a new pack of M&Ms :) I use the bit mostly for the final cutout of my projects. I’m pretty much buying all my bits from IDC Woodcraft from now on.

Carbide End Mill Bits

Sid Harvey’s operates a network of branches from Maine to South Carolina on the East Coast, moving west throughout the Midwest to the Rocky Mountain region. The branches are supplied with more than 50,000 SKU products on a continual basis from our distribution center in Wilkes-Barre, PA. Our manufacturing plant in Andrews, SC is the source for more than 1,700 Sid Harvey brand name products, both new and re-manufactured.

Do one better. Get the Long Router Bit Combo Set. It comes complete with a long 1/4 router bit (down-cut) AND a long 1/8 CNC router bit (down-cut)? Click here to check it out!

Sid Harvey’s operates a network of branches from Maine to South Carolina on the East Coast, moving west throughout the Midwest to the Rocky Mountain region. The branches are supplied with more than 50,000 SKU products on a continual basis from our distribution center in Wilkes-Barre, PA. Our manufacturing plant in Andrews, SC is the source for more than 1,700 Sid Harvey brand name products, both new and re-manufactured.

End Mill bits for wood

With a whopping 3/4" depth of cut per pass,  80ipm plunge rate (yes, I said plunge rate), 80ipm feed rate, and 80% step-over, this bit kicks serious ass when it comes to getting material removed, so you can follow up with your finishing bit to finish your job off.

End Millbitsizes

I have used many popular CNC bits and the Woodcraft bits are great !!! From the Badger to the Beast, to the round overs and 3/16 compression and don't' forget the ultra Clean cutting V-Bitts. I work them and they work for me. You cant beat the personal touch and service either. Sincerely Charles D.

I use this bit every day, not to mention I broke it the first time I used it, and they sent a replacement out immediately no questions asked. Now the story begins that bit showed up during Helene and was displaced from its delivery point my front door, when I arrived there was no package so I contacted IDC so they knew it was not delivered as per the tracking. We waited about a week and a half to see if it showed up and then idc put in a claim with usps, and sent out a new bit. Now it’s time for Milton and the first package is found by a neighbor and returned to me. Now the other it shows up and when I contact Garrett to return it he says no worries just hang on to it. It is super rare to have a company stand behind there products like that. Thanks again Garrett I appreciate you and all your people.

End Mill Bits for Aluminum

But it's not just a time thing. Making the roughing endmill CNC router bit your workhorse for major material removal on your CNC woodworking projects, you save a ton of wear and tear from your regular up-cut, down-cut, or compression router bits. You'll only use them to do the finishing work.

End mill bits for drill press

Can’t say enough about The Hog, matter of fact all of the bits through IDC are top notch and are my go to bits on any job.

Watch the HOG rip through wood at fantastic feed rates. The extended reach flutes allow you to carve deep pockets in your projects in no time flat!

End Mill Bits for Steel

Plainly put, the up-cutting long 1/4 roughing endmill bit is the CNC bit to use when you need to remove massive amounts of material!

If you're looking for speed to rough out your CNC router projects, the long 1/4 roughing endmill CNC router bit is the one you want!!. We call it the 'HOG' here at IDC Woodcraft because it literally is a hog when it comes to removing material mind-blowingly fast from your CNC woodworking project.

That alone extends the life of your bits significantly, saving you money for replacements. At $40-ish bucks a pop, the long 1/4 roughing endmill will 100% save you some cash. Especially when it comes to hardwood.