HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Top 10precious metalslist

Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

The tech bundle for independent RIA firms - Save on your existing tech, and also take advantage of better pricing on the new tools you've been eyeing.

Precious metalslist by value

The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Choose from our selection of lathe tool inserts, including economy carbide inserts, carbide inserts for multiple materials, and more.

8 precious metalsprice

Sep 16, 2022 — In this guide, we share some information on the anatomy of a drill bit to show you what they are made of and how they are measured.

The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

List ofprecious metalsand stones

Discover Puebla temperature by month. From 23°C (73°F) in January to 28°C (82°F) in April. Check the average and current temperature in Puebla.

Connecticut Saw & Tool is a sales and tool sharpening service for wood, plastic, and metal. Stratford, Connecticut, United States 11-50 Private ctsaw.com

Except for those rare few souls that write N/C programs for the sheer joy of it, the ultimate purpose of owning, programming, or operating an N/C machine tool is to make a buck. The buck is made by performing a service or making a product better and at lower cost than the competetion can do it. One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

5 Flute Roughing End Mills: High metal removal, enhanced productivity, and chatter suppression for diverse materials.

One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Genmitsu 30pcs PCB Drill Bits Set, 0.1mm-3.0mm, 1/8" Shank Spiral Flute CNC Router Bits for Print Circuit Board Jewelry CNC Engraving, PD30A

8 precious metalsworth

Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000.

8 precious metalsvalue

Please make sure your browser supports JavaScript and cookies and that you are not blocking them from loading. For more information you can review our Terms of Service and Cookie Policy.

For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

WALTER TOOLS SPJW Carbide Milling Insert. Worldwide Delivery | Buy online or via Purchase Order | +44 203 287 5224 sales@raptorsupplies.com.

Oct 24, 2011 — ... angle which causes the drill bit to dig in and grab. After grinding ... Vee block fixture holding the tool on the gauge pivots to let ...

For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

8 precious metalsfor sale

With these specialized drill bits, you can cut consistenly clean holes in acrylic plastic. They are also good for cutting consistent-diameter holes in other ...

The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

8 precious metalslist

Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved