Woodruff, or keyseat/keyway cutters are used to cut keyslots into parts, for example shafts. The cutting tools have teeth perpendicular to the outside diameter to produce suitable slots for woodruff keys.

It is clear that it is beneficial to consider the probability distribution of the tolerances and perform a statistical analysis

This is quite simple. A tool with a large diameter is able to mill the part quicker. Limitations apply based on the geometry of the final part.

Vmctoolslist pdf

In the example above, all tolerances were +/-1, so the total height variation is: Ttot = √(12 + 12 + 12 + 12) = 2. The stack of parts will have a height of 40 +/-2. And 0.3% of the stacks will be smaller or larger (with a height of 36 .. 38 or 42 .. 44).

As the name says, these are pretty much end mills with a slight difference. The roughing end mill has jagged teeth. These make the cutting process faster than with a regular end mill.

CNCturningtoolsname PDF

There is a special cutting tool for milling involute gears. There are different cutters available to produce gears within a certain number of teeth.

A common assumption is that the tolerance limits coincide with the +/-3σ (3x standard deviation) values. As a reminder, the standard deviation is a measure of variation. 99.7% of the population falls within the +/-3σ limits.

Cemented carbide is another step towards high performance milling because of the aforementioned properties of such milling machine tools. In the long run, they are a more cost-efficient choice while the up-front costs are higher.

For example, if certain inside radii are necessary, the tool cannot deviate from them. At the same time, you can use a large tool for milling away the bulk of it and apply a smaller one to finish the inside corners.

Cutting ceramic tools are prone to cracking when used on hard materials and with high temperatures. Therefore, they are not really suitable for machining steels, for example. Otherwise, a short tool life is to be expected.

A predecessor for the end mill. Side-and-face cutters have teeth around the circumference as well as on one side. This makes the functionality very similar to end mills but their popularity has waned over the years with the advancement of other technologies.

CNCtool type code

Regular carbon steels are usually out of the option pool because of their limited capabilities. HSS (high-speed steel) is therefore the most inexpensive one to get the job done. At the same time, its rate of wear means that in the long run, there are better options.

These tools usually have a flat bottom but not always. Round and radiused cutters are also available. End mills are similar to drills in the sense that they can cut axially. But the advantage for milling lies with the possibility of lateral cutting.

A tolerance analysis spreadsheet is available in the Engineering Toolkit of Vink System Design & Analysis. This allows you to quickly start performing tolerance analysis, including the statistical method described here. The advanced method as described in ‘Advanced Method of Tolerance Analysis‘ is also possible.

A widely used method for performing a statistical stack-up tolerance analysis is the Root-Sum-Squares (RSS) method. Variances (the standard deviation is the square root of variance) can be added. This makes it easy to sum normally distributed tolerances: Ttot = √(T12 + T22 + …. Tn2).

In the Worst-case Tolerance Stack-up Analysis article, you will read about worst-case or linear stack-up analysis. Such an analysis assumes that all dimensions in the tolerance chain have worst-case deviations from their nominal values. A statistical tolerance stack-up analysis considers the probability of a tolerance value and the combination of tolerances. It turns out that the probability of a worst-case combination is negligible for even a small number of parts. Let’s look at the following example. Suppose you are making a stack of 4 identical parts and you want to analyze the total height of the stack. The parts have a height specification of 10 +/-1. Now assume that all parts have a worst-case deviation and are either 9 (part ‘9’) or 11 (part ’11’) high (any dimension, mm, inch, meter, etc.). With only 4 parts, it is still possible to write down all possible combinations.

Threading operations are usually carried out on drilling equipment. Using a thread mill, though, is more stable and has fewer limitations regarding the environment.

These tools have the same function as face mills. They consist of a central body that holds either one or two tool bits (double-end fly cutters).

Ball cutters, also known as ball mills, have hemispherical cutting tips. The objective is to maintain a corner radius for perpendicular faces.

Slab mills are not that common with modern CNC machining centres. Rather, they are still used with manual milling machines to quickly machine large surfaces. That is also why slab milling is often called surface milling.

If similar parts have been produced, you have important data to make a good estimate of the tolerance distribution. But what if you’re working on a new product and don’t have that kind of data to compare?

Cobalt-bearing HSS, for example, are suitable for even quicker milling. This makes them sufficiently adequate for most jobs.

One of these automated fabrication methods is CNC milling. It is a process where rotary cutters remove material, which makes it the opposite of CNC turning.

Face mills cannot cut axially. Instead, the cutting edges are always located on the sides of the cutting head. The cutting teeth are replaceable carbide inserts.

Choosing the right milling cutters for your job needs an understanding of the materials, parameters and definitely some experience. The final outcome depends on these choices and a machinist must understand what material cutters are suitable for cutting different mediums.

High-speed steel, a grade of tool steels, has a few alloying elements added to it to provide better response to heat and wear than regular carbon steel. While the life cycle of such a tool goes up, so does the cost.

Cutting ceramics are even harder than cemented carbides but lose in the toughness aspect. Both aluminium oxide and silicon nitride are used to produce these tools with varying properties.

CNC toolslist

This material is harder than high-speed steel but the toughness qualities are not that impressive. The higher hardness provides better protection against wear but lower toughness levels make it a little more susceptible to cracking and chipping.

As is the norm in manufacturing, the choice of method or tool comes down to a balance between speed, cost and quality. The cost depends on both the price of the tool, the wear machining results in and the time it takes (speed) to produce the parts.

CNCmachinetoolslist pdf

These are two of the most prevalent milling operations, each using different types of cutters – the and mill and the face mill. The difference between end milling and face milling is that an end mill uses both the end and the sides of the cutter, whereas face milling is used for horizontal cutting.

The probability of an extreme thickness is 2/16 = 12.5%. If, for example, only the top pile is problematic, the probability is only 6.25%. Note that this is an extreme tolerance distribution with a low probability itself. In practice, the probability of an extreme height is very low.

CNC cutting toolsname

The cheapest of the bunch. And this is exactly why it still finds use. As carbon steel is not very durable, it is only suitable for low-speed operations.

Face mills are better for high quality cutting. Fly cutters are just cheaper and the cutting bits are often made at the shop by a machinist rather than bought from stores.

CNC machining is a highly utilised subtractive manufacturing technology. Computer numerical control systems offer less need for manpower and higher levels of automation.

CNCtool types images

As you could see, there are a lot of different machine tools available for a wide range of purposes. The same applies to the materials used to make these tools.

Such a coating reduces the stickiness of the cutting material which can be a problem with aluminium. Therefore, less lubricant is necessary during the cutting process.

The helix angle, along with the rotation speed of the spindle, determines the cutting speed or feed rate. A steeper angle is suitable for softer materials and metals.

CNCturningtoolsname list

In the worst case example above, there was an extreme distribution of tolerances. The question now is what is a (more) realistic distribution. This is not an easy question to answer, but a better estimate would increase the accuracy of your analysis.

The name of this tool says everything you need to know about its purpose. Thread mills are used for producing tapped holes.

If you don’t know the distribution of tolerances, you have to make an estimate. It is often assumed that tolerances have a normal (Gaussian) distribution. This is because the normal distribution seems to occur in “almost all cases”. In statistics, this is called the central limit theorem. Roughly speaking, this theorem states that “the sum of a large number of independent and identically distributed random variables, will be approximately normally distributed“. Since the manufacturing process of machined parts consists of many variables, it is safe to assume a normal distribution of tolerances. An added benefit is that it is relatively easy to add up normally distributed tolerances.

The milling centres do not just perform the cutting automatically, but also the changing of tools. During the average process of creating a finished product from a block of metal, for example, various tools are used.

There are some different coatings available to protect the tools from wear. For example, a titanium nitride coating increases the tool’s lifespan but also the cost of it.

The cut bits of metal are smaller than usual and therefore easier to clear. Multiple teeth come into contact with the workpiece at the same time. This reduces chatter and vibration, which could otherwise be larger because of the jagged teeth.

Hollow mills are basically the opposite of face mills. Here, the workpiece is fed into the inner part of the mill to produce a cylindrical outcome.