Manufacturing facilities have complex machinery to put threads in parts with ease.  They have things set perpendicular to run perfectly — usually with dedicated machinery.  For DIY we don’t have that convenience nearly as much.  We need to rely more on our own setup and skill.

We also have a wide selection of tumbling media for various industrial applications including automotive, medical, electronics, and jewelry.

When heft is on the agenda, consider this beefy version of our 14K / 16K by 20’ length deck-over trailer plans.  With many options like all our trailers, this tandem axle is super heavy duty for rigorous jobs.

The video shows a simple way to align things when thread tapping.  Using the same set-up as when you drill the hole, leverage the location and vertical position of the drill press to hold the tap straight.

So, what about using machinery to assist?  Sure, that works too.  But, do it really carefully.  Here’s a quick video of thread tapping into the ends of some aluminum extrusions.  The component not shown in the video is the vise attached to the press table, hanging over the edge of the table to allow drilling into the end of the long work-piece.  (Sorry, I should have shown that.)

You can use this machine to repair wheels up to 30 inches in size. The maximum spindle speed supported by this model is 1500 rpm. It is fitted with a powerful 7.5 KW motor. The operator can enter all the processing parameters on the outer panel of the machine. Inovatec machinery also offers customization of this wheel repair CNC lathe machine according to customer needs.

Tap tool ends can be different based on what you’re trying to do.  Here are a few below.  The more threads that in the chamfer, the easier it is to get the tap to start straight, but the deeper you have to tap to get the same number of full threads.  The “Plug Chamfer” is the most common.  (Images from McMaster.com – best website ever.)

Finally, what if the tap binds in the hole?  This can happen if the chips get too bungled up, or if the tap is at a slight angle.  If the tap gets stuck, treat it carefully because you definitely don’t want to break it.  I find the best thing is to twist in back and forth.  Start with light pressure, and apply more and more each time.  Turn left, then right, then left again and again.  Put a little oil down the hole too.  For me, the taps have always, eventually, come loose so I can back it out.

Change the trailer plans from Leaf Springs, to a Torsion Axle Trailer.  These plans show you how.  The design fits Mechanical Elements 4', 5', 6' and 6'10" Widths - for 3500 lb, Single Axle Trailers.  Select your width.

Blueprints for a Strong and Stable 6x12 utility trailer.  This single axle, 3500# capacity trailer with many options is ideal for a million uses.  We provide great DIY Plans for builders who want the best.

There are several versions of taps available.  Just a quick look online will show straight taps, spiral taps, bottom taps and chip clearing taps (just to name a few).  There are a lot of specialty tools, and specialty options, so don’t worry too much about all the details.

The high quality raw materials used in the manufacturing of the WRC28VM wheel repair CNC lathe machine ensure a long lifespan of the machine

If you’ve ever cross threaded a nut, then you know the issues if you don’t start the thread in straight.  That is exaggerated with a tap (and even more so with a die).  If you don’t get the tool straight with the hole to begin, it can make a bit of a mess.  That said, taps can be fairly forgiving and follow the hole if you’re careful.

3-Jaws Chuck（With Special Soft Jaws) Manual Quick Change Toolpost,four-station turret Automatic lubrication system Turning the cooling system With probing system (TP300 Pioneer Sensing Probe TP300) Diamond Cutter 1 set CNC controller syntec brand Full Enclose Security Door Digital Optimization Software design for wheel Training Video CD Work Lighting System

Good luck with all your tapping.  Next up . . . read about what we consider the most important tools to have in the shop.

Conceptually, threading a hole is easy.  Just drill the right size hole, then put the tap end in the hole and start twisting.  But what if the tap does not enter the hole straight?  What if you need to tap a hole right to the bottom?  What if the tap binds in the hole?

It is important to note that with aluminum this is less risky, but with steel, depending on the alloy, the forces internal to the tap can be really high.  With Steel and with other materials, especially when tapping is deep, be super careful with this technique, and use a lot of oil, because it’s a big hassle to dig out a broken tap.

If you’re not that familiar of skilled with tapping, the best advice I can give is go slow.  Take your time and figure it out.  Test a bit with scraps of material that don’t matter.  You’ll get the hang of it pretty fast, because it’s not that complicated (from a high level view).  I’m not trying to minimize because there are a lot of details (like we covered above), but overall the concept is easy.  Try it a bit, and you’ll learn quick.

From vibratory finishing machines to centrifugal disc and barrel finishing machines, we produce all sorts of finishing tools.

Based in China, we are a mass finishing equipment and media manufacturer with a renowned global clientele, including Bosch, Swatch, and Toyota.

Invention of the thread has to be one of the greatest accomplishments.  Conceptually, it’s just a ramp wrapped around a rod that allows you to slide another ramp (equal and opposite) wrapped inside a hole until something causes them to stop — namely, the bolt gets tight.  With one inside the other, the continuous ramps are in contact with angles that keep them from sliding back.  That is, while under load the friction overcomes the sliding forces.  (Until, of course, other forces are present — like vibration, or you turning it with a wrench.)

The WRC28VM Vertical Diamond Cut Wheel Repair CNC Lathe Machine helps to repair wheels at a faster rate. It comes with a strong and sturdy cast iron base. It helps to provide a stable setup for the wheel refurbishing process. The machine also comes with a fast cutting rate of 1000 mm/min.

That’s the theory, and the way we accomplish it is to cut (or roll) the ramp (thread) into the two pieces, male and female.  Hence, the tap and die.  A tap puts internal threads in a hole (like a nut).  A die puts external threads on a shaft (like a bolt).

For this article, we’ll focus on the tap for cutting internal threads.  These are far more common for DIY simply because we can so easily buy the external threads in the form of a bolt.  Yes, we can also buy nuts (internal thread), but we sometimes need those internal threads in the part rather than adding a nut.  That’s where the tap comes in.

The aluminum extrusion is not the important part, it’s using the drill press to do the thread tapping.  Note that while the spindle is turning continuously, there is no chip breaking.  After the spindle stops, we need to do the chip breaking to avoid getting the tap stuck.

Sometimes, doing it all by hand (without the drill press), the tap will go in slightly angled, and that messes up the start of the hole.  That is more true when using bottoming taps.  Lots of care in the start is really important.

One of the things I dislike most about tapping threads is the repetitive and time consuming nature of it.  Twist down, then back it just a little to break the chips, then twist down again.  Over and over for as many threads as you need.  If you need to go deep in a blind hole, then every once in a while you should back it out (mostly), blow the chips away, then twist it down to continue cutting.  For fine thread bolts, that can be a lot of twisting over and over.  If I have to do several, it’s just annoying.

A Tap and Die set is a near must for a DIY fab shop.  While the thread creating functions are pretty easy to visualize, sometimes getting the tread to start straight and run true is a different matter. The thread tapping functions are easiest, so let’s talk about that first.  Dies are are less frequent, and tend to be more difficult to start perfectly straight.  Since that’s really another topic, if you’re interested, there’s this article about Successful Threads With A Die.  In the meantime, let’s get back to internal thread tapping.

There is a lot written and a lot on video about thread tapping, so I’ll skip the details.  However, I will review just a couple things that help to get it right.

That’s about it.  There is a ton of additional information about the tapping tools and about tapping in different metals.  Just search on-line and you’ll find as much detail as you want.  To me, it’s fascinating to look at the different cutting and tooth geometry for various metals, and the many different cutting fluids available.  Those are probably important for production environments, but for us in DIY, a good General Purpose tap with some sort of oil seems to work well enough for just about everything.