2005C - Roundover Bit Double Flute Roundover Bit 1/2" Shank 1/8" Radius 3/4" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge ...

Depth of Cut: The maximum depth of cut (DOC) for a specific insert. The maximum DOC is affected by many variables, and may not be achievable under all conditions.

90° cutting edge | D.O.C. max. 0.394" (10.0mm) • Positive axial rake, positive radial rake • 35-degree rhombic inserts with two different nose radius options • High polish for excellent surface finish and reduced built-up edges • Large chipbreaker grooves for controlled chip evacuation • Low cutting forces due to the positive cutting edge

AMS-556 4-Pc Carbide Tipped Corner Rounding & Beading Router Bit Set, 1/2 Inch Shank Shank (d): 1/2" Includes: 1/4" Radius 3/8" Radius 1/2" ...

45° cutting edge | D.O.C. max. 0.236" (6.0mm) • Negative axial rake, positive radial rake • Double-sided, extra-thick insert with 8 cutting edges • Low cutting loads and excellent smooth cutting

1978 - Small Pilot Roundover Double Flute Roundover Bit 1/4" Shank 1/16" Radius 3/8" Large Diameter 7/16" Cut Length 2" Overall Length Extra smal...

Curved edge | D.O.C. max. 0.039" (1.0mm) • Low entering angle for high feedrates • High cost-efficiency, with 4-corner inserts • Positive rake angle for lower cutting forces • Wide flank face for rigidity and strong clamping

2010 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 3/4" Radius 2" Large Diameter 1" Cut Length Roundover bits provide a curved edge to yo...

2003 - Roundover Bit Double Flute Roundover Bit 1/4" Shank 3/8" Radius 1-1/4" Large Diameter 5/8" Cut Length Roundover bits provide a curved edge...

2016 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 1-1/2" Radius 3-3/4" Large Diameter 1-7/8" Cut Length Roundover bits provide a curved ...

90° cutting edge | D.O.C. max. 0.591" (15.0mm) • Positive axial rake, positive radial rake • Sharp cutting edge geometry, and robust inserts • First choice for large cutting depths with high feedrates • Specially designed cutting edge, for high-quality shoulder milling

MRR108 Carbide Tipped Miniature Corner Rounding 1/16 Radius x 5/16 Dia x 5/16 x 1/4 Inch Shank with Mini 3/16 Dia Lower Ball Bearing Diameter (D)...

45° cutting edge | D.O.C. max. 0.236" (6.0mm) • Positive axial rake, positive radial rake • Large rake angle for faster, easier cutting • Inserts with 4 cutting edges

2009A - Roundover Bit Double Flute Roundover Bit 1/2" Shank 5/8" Radius 1-3/4" Large Diameter 1" Cut Length Roundover bits provide a curved edge ...

There are several variables that go into choosing the correct insert for your milling operations: the specific cutter body being used (milling cutter series), the type of machining operation (toolpath type), the cutting-edge angle (lead angle), the depth of cut, the materials being cut, and more. Use the filters on the left-hand side below to narrow down your choices, and find the inserts you need.

90° cutting edge | D.O.C. max. 0.303" (7.7mm) • 90-degree shoulder mill • Double-sided, thick insert for high stability and deeper cuts • Inserts with 6 cutting edges

MR0110 Carbide Tipped Miniature Corner Rounding 3/32 Radius x 3/8 Dia x 3/8 x 1/4 Inch Shank with Mini 3/16 Dia Lower Ball Bearing Diameter (D): ...

Material Type: Filter by primary workpiece material to find the inserts that are best suited for that specific material. You can also then filter by secondary workpiece material to find inserts that will cut multiple materials.

2001 - Roundover Bit Double Flute Roundover Bit 1/4" Shank 1/4" Radius 1" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge to ...

straight and true. First time using Iroko. Outdoor mostly sheltered area.Not Teak but still quite pricey. KJP is a great company to deal with, like a candy store for wood

2006 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 1/4" Radius 1" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge to ...

90° cutting edge | D.O.C. max. 0.67" (17.0mm) • Designed for high-speed machining of aluminum • Buffed surface for smooth chip evacuation and reduced BUE • High rake angle for good surface finish and lower cutting loads • For square shoulder milling and curved surface machining

90° cutting edge | D.O.C. max. 0.649" (16.5mm) • Superior perpendicularity and minimized cutting loads • Optimized for high-quality surface finishes • High rake angle lowers cutting loads and minimizes burrs • High-speed and high-feed capability improve productivity

2000 - Roundover Bit Double Flute Roundover Bit 1/4" Shank 3/16" Radius 7/8" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge ...

Round edge | D.O.C. max. 0.236" (6.0mm) • Superior perpendicularity and minimized cutting loads • Optimized for high-quality surface finishes • High rake angle lowers cutting loads and minimizes burrs • High-speed and high-feed capability improve productivity

2000A - Roundover Bit Double Flute Roundover Bit 1/4" Shank 1/16" Radius 5/8" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge...

90° cutting edge | D.O.C. max. 0.217" (5.5mm) • Superior perpendicularity and minimized cutting loads • Optimized for high-quality surface finishes • High rake angle lowers cutting loads and minimizes burrs • High-speed and high-feed capability imrpove productivity

Not impressed with the shipment I received, the 12x12 was not 12x12, off an 1/8 to a 3/16 on both sides and the peices were very warped and not flat

90° cutting edge | D.O.C. max. 0.63" (16.0mm) • Positive axial rake, negative radial rake • 3D helical cutting edge for lower cutting forces • Wiper geometry for high-quality surface finishes • Superior perpendicularity and minimized cutting loads

2009 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 1/2" Radius 1-1/2" Large Diameter 3/4" Cut Length Roundover bits provide a curved edge...

15° cutting edge | D.O.C. max. 0.071" (1.8mm) • 15-degree high feed mill • Inserts with 4 cutting edges • Ramping possible • Double clamping system for inserts

2008 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 3/8" Radius 1-1/4" Large Diameter 5/8" Cut Length Roundover bits provide a curved edge...

MR0112 Carbide Tipped Miniature Corner Rounding 1/8 Radius x 7/16 Dia x 3/8 x 1/4 Inch Shank with Mini 3/16 Dia Lower Ball Bearing Diameter (D): ...

2000C - Roundover Bit Double Flute Roundover Bit 1/4" Shank 1/8" Radius 3/4" Large Diameter 1/2" Cut Length Roundover bits provide a curved edge ...

45° cutting edge | D.O.C. max. 0.217" (5.5mm) • Negative axial rake, positive radial rake • Double-sided inserts with 16 cutting edges • Special geometry for consistent cutting and long life • Strong insert and powerful clamping

90° cutting edge | D.O.C. max. 0.571" (14.5mm) • Negative axial rake, positive radial rake • 90-degree shoulder mill with rectangle insert • Double-sided, thick inserts for high stability and deeper cuts

17.23° cutting edge | D.O.C. max. 0.07" (1.8mm) • Negative axial rake, negative radial rake • Positive rake angle for lower cutting forces • Strong vibration and impact resistance • Large chip pocket for smoother chip evacuation

2012 - Roundover Bit Double Flute Roundover Bit 1/2" Shank 1" Radius 2-1/2" Large Diameter 1-5/16" Cut Length Roundover bits provide a curved edg...

45° cutting edge | D.O.C. max. 0.138" (3.5mm) • Positive axial rake, positive radial rake • 45-degree cutting edge • Inserts have 8 cutting edges • Screw clamping

45° cutting edge | D.O.C. max. 0.275" (7.0mm) • Negative axial rake, positive radial rake • Double-sided, extra-thick insert with 8 cutting edges • Large rake angle reduces cutting forces • Wiper insert geometry for good surface quality

1980 - Small Pilot Roundover Double Flute Roundover Bit 1/4" Shank 1/8" Radius 3/8" Large Diameter 7/16" Cut Length 2" Overall Length Extra small...

This price includes shipping cost, export and import duties, insurance, and any other expenses incurred during shipping to a location in France agreed with you as a buyer. No other mandatory costs can be added to the delivery of a Haas CNC Product.

Milling Cutter Series: Filter by the Haas Milling Cutter Series to find all the inserts available for that specific cutter. If you don’t know the cutter series (or have a non-Haas cutter body), you can also filter by insert style (shape), or ANSI designation.

1982 - Small Pilot Roundover Double Flute Roundover Bit 1/4" Shank 1/4" Radius 5/8" Large Diameter 1/2" Cut Length 2-1/8" Overall Length Extra sm...

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

90° cutting edge | D.O.C. max. 0.217" (5.5mm) • Superior perpendicularity and minimized cutting loads • Optimized for high-quality surface finishes • 3-face clamping for stable operation in tough conditions • Suitable for plunge milling

90° cutting edge | D.O.C. max. 0.059/0.098" (1.5/2.5mm) • Double-sided inserts with 4 cutting edges • Unique geometry for lower cutting loads and longer life  • High rake angle with strong, sharp cutting edges • Designed for high-efficiency plunge milling