It’s important to get precise cutting data for your applications no matter what brand of tool you’re using. With the Seco Assistant there's no need to browse through catalogs or print outs. It provides easy-to-use machining information, including speed and feed calculators, material removal rates and more. This helpful information makes set up faster, increasing productivity on your shop floor. Many of the features work offline.

This formula is used to calculate the feed per tooth from the table feed per minute (feed rate), the number of teeth, and the spindle speed. Example: Table feed per minute (vf) = 450 mm/minNumber of teeth (z) = 10Spindle speed (n) = 600 min-1In this case, the feed per tooth (f) is 0.075 mm/t.

This formula is used to calculate the machining time from the total table feed length and the table feed per minute (feed rate). Example of finishing a block of FC200 cast iron to have a flat surface of: Width = 150 mLength = 250 mmFace milling conditions used: Feed per tooth (fz) = 0.35 mmNumber of teeth (z) = 12Spindle speed (n) = 200 min-1Cutting speed (vc) = 120 m/minFace mill diameter (D1) = 220 mmIn this case, the table feed per minute (vf) and the total table feed length (L) are:vf = 0.35 × 12 × 200 = 840 mm/minL = 350 + 220 = 570 mmSubstitute these values into the formula: Tc = L ÷ vf = 570 ÷ 1120 = 0.679 (min) × 60 = 40.74 (sec)The machining time (Tc) is approximately 40.74 seconds.

Feb 24, 2024 — A high-speed mill is a type of milling that involves fast, lighter cuts using high spindle speeds and specific tools. It replaces slow, heavy ...

Stone Setting Burrs - High Quality Jewellers Burrs from the USA - From Gemcuts, your Complete Jewellery Tool Supplier.

OLIVE TREE PEOPLE replaces the 70% water content, which is normally used in skin care products, with the globally unique holistic beauty molecule and elixir ...

This formula is used to calculate the net power required for face milling based on the depth and width of cut, the table feed per minute, the specific cutting force, and the machine efficiency. Example of calculating the net power required to cut tool steel with: Depth of cut (ap) = 5 mmWidth of cut (ae) = 70 mmTable feed per minute (vf) = 300 mm/min Other conditions: Specific cutting force (Kc) = 1800 MPaMachine efficiency (η) = 80% (0.8)Cutting speed (vc) = 80 m/minCutter diameter (DC) = 250 mmNumber of teeth (z) = 16 In this case, first you calculate the spindle speed (n) and then the feed per tooth of the cutter (fz). Spindle speed (n) = 1000・vc ÷ π・D = (1000 × 80) ÷ (3.14 × 250) = 101.91 min-1Feed per tooth (fz) = vf ÷ (Z × n) = 300 ÷ (16 × 101.91) = 0.184 mm/toothSubstitute the above into the formula: Pc = (5 × 70 × 300 × 1800) ÷ (60 × 106× 0.8) = 3.937 kwThe net power required for face milling (Pc) is approximately 3.94 kW.

We distinguish ourselves as the #1 choice for industrial manufacturers who are in need of Technical Service and Production Savings. We are their across the ...

This formula is used to calculate the table feed per minute (feed rate) from the feed per tooth, the number of teeth, and the spindle speed. Example: Feed per tooth (fz) = 0.2 mm/toothNumber of teeth (z) = 8Spindle speed (n) = 600 min-1In this case, the table feed rate is 960 mm/min.

C2G 27247 "C2G 5ft Shielded Cat5E Molded Patch Cable networking cable Red 60"" (1.52 m)" · Today's mission critical advanced Fast Ethernet and Gigabit computer ...

SFM to RPM

Bahia Principe is hiring. See post for available positions and submit your application today. Follow @careerjamaica for the latest job ...

Timetable for TransLink bus route 509 at stop 57260 - Eastbound 96 Ave @ 210 St.

This page introduces formulas for calculating basic parameters necessary for face milling. The figures obtained from the calculation are for reference only. The conditions for machining depend on the machine tool you are using. Use the optimal conditions according to your actual machining circumstances.

essential changes), all the sections of the Single Form will be displayed automatically. The partner will then update the sections relevant to the ...

Tapping Speed

Never used UTG Picanny Rail Riser • Precision CNC Machined from 6061-T6 Aircraft Grade Aluminum and Finished in a Matte Black Anodize • Distinctive ...

This formula is used to calculate the cutting speed from the spindle speed and the outer diameter of the cutter. Example: Cutter diameter (DC) = 100 mmSpindle speed (n) = 400 min-1In this case, the cutting speed (vc) is approximately 125.6 m/min.

It's also easy to use. After choosing a subcategory and filling in the parameters, you'll receive machining details that you can export to a PDF to share with your colleagues or your Seco representative.

STAINLESS STEEL 400 SERIES. 409, 410, 414, 420,. 430, 436, 442, 446. 135 - 325. DISCONTINUOUS. TIGHTLY CURLED. 200 - 400 .003-.006. STAINLESS STEEL. FREE ...

Calculate the best parameters for your application It’s important to get precise cutting data for your applications no matter what brand of tool you’re using. With the Seco Assistant there's no need to browse through catalogs or print outs. It provides easy-to-use machining information, including speed and feed calculators, material removal rates and more. This helpful information makes set up faster, increasing productivity on your shop floor. Many of the features work offline.Equally importantly, it covers a range of materials and applications, including:MillingShoulder MillingDisc MillingFace MillingSolid MillingTurningGeneral TurningGroovingTurning 3-passHolemakingIndexable Insert DrillsSolide Carbide/ Exchangeable Tip DrillsBoring 3-passThreadingThread TurningThread MillingThread Turning Helix It's also easy to use. After choosing a subcategory and filling in the parameters, you'll receive machining details that you can export to a PDF to share with your colleagues or your Seco representative.Download the AppTo get quick access to cutting data and more, download the app now.Seco Assistant App for iOSSeco Assistant App for Android