RPM to SFM: Calculator, formulas, and Charts - surface feet per minute to rpm
Materialremoval ratein milling
The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
This is a page about postal code of Settimo, Verona, Veneto, with more professional information like latitude, longitude and online map etc. ... This is online ...
Metal removal rateformula
For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
We offer PN 2931 - DIN 338 RN standard with TiN and - PN 2905 T1000, PN 2907 T1000, PN 2915 T1000, and ZV3001 T1000 with TiAlN coating in our catalogue. Our other ground from solid tools are coated on customer requests. Please, send your questions and requests to Frantisek Raszka. mail: raszka@stimzet.cz
HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Taps. Taps are cutting tools used to create or chase screw threads on the inside surface of a hole. KnKut spiral point taps actually cut the ...
Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Dec 7, 2023 — Made from high-speed or cobalt steel (HSS), metal drill bits are ideal for general metal drilling applications, while cobalt steel drill bits ...
MaterialRemoval Rateformula for drilling
Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Tested drill: drill HSS DIN 338 diameter: 6 mm drilling depth: 15 mm drilled in material: 1.2379 material strength: 800 N/mm2 cooling: emulsion 5%
it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
To assist with your tool holder selection, we've developed this quick video comparing the five most common holder types: side-lock end mill holders, shrink-fit ...
Materialremoval rateunit
Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Materialremoval rateformula for milling
In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Contact Ideal Coatings & Fabrication Ltd is a one-stop shop for all your Coatings, Field Coating, and Fabrication requirements. Call 780-532-7350.
Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Huge Upgrade:HWHUNO tapered square nails are actually tapered square nail tips,the others are just very slightly 1% tapered square which are still pretty wide, ...
Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000.
Metal removal ratechart
No it's not a step bit, it's called a counterbore. You buy them with an integral or inserted pilot that's the diameter of the original hole and ...
Nov 24, 2020 — This post discusses the basics of CNC machining titanium, including the most suitable applications, machining considerations, and surface finishing options.
Except for those rare few souls that write N/C programs for the sheer joy of it, the ultimate purpose of owning, programming, or operating an N/C machine tool is to make a buck. The buck is made by performing a service or making a product better and at lower cost than the competetion can do it. One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Materialremoval rateCalculator
234 Multi Form Plastics jobs available on Indeed.com. Apply to Deli Associate, Process Technician, Manufacturing Supervisor and more!
Materialremoval rateformula for turning
HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
Download Table | Task Specific rPT and iPT Performance Data for Novices and Experts from publication: Validation of a Novel Inverted Peg Transfer Task: ...
For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved
The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next: Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved