So many times we need to make matching holes to bolt something on.  You purchased something to mount on your trailer or your workbench or some other project, but now you need the exact aligning holes to bolt it on.  There are obviously many ways to accomplish it, but when this option is available, here is a super easy way to drill matching bolt holes perfectly every time.  And, the best part — you don’t have to measure much.

Match drillingkit

But, what if we get one of the holes a little off?  What a hassle.  Go back and drill the holes a little larger till we can make it fit.  Or, work to elongate a hole to make it fit.  Or, maybe use this technique to force things to fit.  Any way we do it, it’s a hassle and it turns out less than what we wanted.

When the above methods don’t work — either because of the awkward nature of the part you are attaching, or some other reason — we can use transfer marking.  The two ways to accomplish it are:  1) with a pen;  2) with a transfer punch.

Mounting a trailer tongue hitch is an example.  We want 1/2″ bolts, but we don’t want to push a 1/2″ drill through a steel beam by hand.  So, we start with a small hole, then make it bigger and bigger with successive larger drill bits.  (Like 1/8″ then 1/4″ then 3/8″, then finally 1/2″.)  Drilling in steps makes big holes much easier.

The essence is locating the new holes by using the new piece as a template for drilling the matching holes.  There are 3 ways this works.

The example shown in the image is perfect for this.  It’s the mounting plate for the I-Beam at the top of the Gantry Crane leg.  We want those holes to match, of course, so using one mounting plate to guide holes in the other plates as well as the beam makes everything line-up.   (In case you want them, here are the I-Beam clamps shown.)

Harvey Cantwell (HRVY) is a singer, model and entertainer who became a social media phenomenon on platforms such as Youtube, Instagram and musical.ly.

Performance Tool 2 3/8in to 2 5/8in Medium Swivel Oil Filter Wrench · Part # W54044 · SKU # 965869 · limited lifetime warranty Limited- ...

Match drillingholes

On the other hand, often you can put a “transfer punch” in the hole and mark the center with the punch.  Transfer punches (shown in this image) are not super common tools for DIY, but nice in these circumstances.  Select the right size punch (largest that will fit the existing hole), and use a hammer to indent the center of the hole into your new part.  Do this for all of the holes while the part is clamped in the correct location.  This will “transfer” the locations of the hole so you can then drill them as needed.

Match drillingaerospace

The method works when you can put the two pieces together easy enough for drilling.  The method does not work when the parts are obnoxious in size or some other thing that precludes the methods below.

Read Backdraft 2 reviews from parents on Common Sense Media. Become a member to write your own review.

Find milling formulas needed for your milling operations, such as how to calculate correct cutting speed, feed per tooth and metal removal rate or specific ...

This is the easiest, but it also has some limitations.  With the direct approach, we drill matching bolt holes by using the item to attach as the template.  We simply clamp it at the desired location (you might have to measure for the first hole), then drill through using the holes of the existing part.  Here’s a video as the explanation:

Sometimes the best you can get is a pen in the hole to draw the position onto the mating part.  (Felt tip markers like SHARPIE work best.)  When you do, make sure the pen is straight up and down as you trace it.  You’ll then need to eye the center and mark it with a punch to drill.  This technique is often the best for thin sheet metal parts.

So, we lay it all out on the steel, with measurements for each hole, then following instructions from this post about drilling, we punch and drill each hole.  Hopefully we did the math right as we set it all up.

Shop our wide selection of drill bit accessories and adapters from top brands including MAXIMUM, Mastercraft, Bosch, and DEWALT.

Bullard Abrasives | Custom Cutting Grinding and Finishing Abrasives. About ... Adjustable Spanner Wrench. $8.36. ADJUSTABLE SPANNER WRENCH. Marvel's adjustable ...

For the sake of illustration, we’ll use a simple example of mounting a taillight.  The light comes looking beautiful, and the website even has some dimensions for the holes.  (Image from etrailer.com).

Match drillingtools

Drill Bits Straight Shank HSS HSCO ... 90 & 120 Degree NC Spotting Drills ...

Anyway, the technique starts like Method 1, using the large drill bit, but only deep enough to leave a good center mark for a guide.  Switch to a small drill bit, drill through, then progress from there.

2022719 — An executive transition approach that goes beyond onboarding to establishing the foundation for long term success.

Corner Cutter · 3 in 1 Corner Rounder Punch 3 Way Corner Cutter for Paper Craft Laminate *WA · 3 in1 Corner Rounder Punch Corner Cutter Hole Edges Punch Card ...

I use these techniques all the time in my shop.  It’s not that I dislike measuring and marking for drilling holes.  However, if we skip the measurements, then we’re more likely to have the right holes in the right spots.  Make the job as simple as possible.  Also, I like it when things just bolt up nice rather than having to fiddle to make things fit.

As a simple modification of Method 1 above, if the hole is large, then we must drill in steps.  For instance, if the holes you need are larger than you want to drill through with a single pass.

Bolt down the vee-block and place a centre drill (Slocombe drill) in the drill chuck. Secure the bar to be drilled in the vee-block and start the cross hole.

First, let’s look at the classic way with measuring and marking.  It’s easy and straightforward, but has several steps with a lot of room for error.

While only the initial drill point mark is truly guided by the existing holes of the part for mounting, that mark sets the hole location for the smaller drills to follow.  This is why we call it indirect drilling.

Match drillingmachine

This follows right along with the concept of quick and easy fixtures.  For many applications, this works great, but the limitations are:

This indirect method is also perfect to drill matching holes to tap.  Tapped bolt holes are smaller than the clearance holes, so we start with the drill point, then end at the proper tap drill size.  In the case of threads, it’s extra important that the holes match as well as for tapping the treads straight.

This is the easy way — when the situation allows you to do it.  I’m sure many of you know and use this method already, so I apologize if the presentation is old news.  However, if you don’t know it, then read on.  It’s a great time saver and it helps you get just the right alignment as you drill matching bolt holes.