Strain hardeningprocess

Bending a paper clip back and forth until it breaks is a demonstration.  The paper clip breaks because it eventually strain hardens so much from being bent, and is so hard that it becomes brittle and breaks.

Hardening a material sounds like a good thing, but there are times when it is undesirable. If nothing else, the material will be harder to machine, cut through, or form during the manufacturing process.  That means it may have to be cut with slower feeds and speeds, or that tool life will suffer.

Physical vapor deposition involves very low pressure (high vacuum) and comparatively low temperatures, typically resulting in very thin coatings.

The root cause of strain hardening is dislocation of the crystal structure of the metal.  This short video has great illustrations of what I mean by dislocations:

Strain hardeningexample

Elastic deformation is deformation that recovers when the stress is removed.  And yield stress is a mechanical property that is the amount of stress needed to hit the exact transition from elastic deformation (lower) to plastic deformation.  Yield stress is often the maximum allowable load on a component because applying more load will cause the component to be permanently deformed.

Strain hardening, or work hardening as it is more often called, is the hardening of metal by plastic deformation.  It can be a problem or a benefit in metalworking.  Learn what it is and how to avoid or encourage it in this article.

The higher the n-value, the more easily the material work hardens.  17-4PH Stainless has an n-value of 0.05, which means it is only minimally work hardening.  But 304 Stainless has an n-factor of 0.45, which means it is very susceptible to work hardening.  I’m sure that’s one reason many machinists are not fond of it.

What is strain hardeningused for

The application of heat must be controlled so the material does not melt. There are guides for most materials that tell you how hot it must get to anneal the material.

That is why venting a high-vacuum chamber is always a major challenge. It is important to aerate them slowly and in a controlled manner, because venting too quickly creates turbulence that stirs up particles in the chamber.

At SMC you get all the components you need for CVD processes and for ventilation and evacuation of your high-vacuum chamber for PVD processes: a wide variety of valves, temperature control units, sensors, etc.

what is strain hardeningin stress-strain curve

Physical vapor deposition only works in high vacuum because an extremely clean environment is essential for the manufacture of microchips, CDs and DVDs. Even the smallest particles are a big problem.

Strain hardening is caused by the dislocations in the crystal structure of the material running into one another. Annealing is the application of heat to force recrystallization that eliminates those dislocations.

What is strain hardeningformula

Materials science has a lot to say about strain hardening, and it isn’t too hard to understand.  Let’s make it a touch more technical, so we have some language to discuss it.  Don’t worry, I have put all the really technical stuff at the very end of the article, so you can easily skip it!

In contrast to physical processes, chemical vapor deposition can also be used to coat surfaces with complex three-dimensional shapes, such as the finest indentations in wafers.

Among the mechanical properties materials have, hardness is often a valuable one.  Various processes can be employed to increase metal hardness when desired, a process called cold working.

What is strain hardeningin steel

Chemical Vapor Deposition (CVD) is a coating process that produces thicker layers and is subject to comparatively high pressure and temperature. The most important application of CVD is wafer coating.

Heat is one of the biggest allies to work hardening. Increasing temperature increases the susceptibility of materials to work hardening.

Strain hardeningDefinition Engineering

In CVD, a substrate is heated, on the surface of which a solid component is deposited from the gas phase as a result of a chemical reaction. In order to be able to deposit the solid layer at a specific reaction temperature, volatile compounds of the layer components must be present.

In theory, any metal or alloy can be strain hardened. What differs is how easily they strain harden and how much harder the get.

Why doesstrain hardeningoccur

Some metals like aluminum and austenitic stainless steel cannot be heat treated or tempered to increase their hardness. But they can be work hardened by peening, rolling, forging, or drawing.

PVD is based on physical vapor deposition. These are vacuum-based coating processes or thin-film technologies. In contrast to the CVD process, the layer is formed here directly by condensing a material vapor from the starting material.

As machinists, we’re often concerned with how to minimize work hardening when working on a material prone to it.  More about that below.

Think about this in relationship to machining operations.  A milling cutter slices and pulls out chips.  Sounds like the pulling out of the chip could be tensile deformation.  On the other hand, if we put the part in a hydraulic press we are applying compressive deformation.

A value called the strain hardening exponent is one way to quantify the degree to which a material will work harden.  Here’s a table showing the strain hardening exponent (the n-value) for a number of common metals:

Plastic deformation is the process of applying enough stress to the material so it is permanently deformed. The process of applying that stress is called “Cold Working” the material.

After strain hardening, the material will be somewhat less ductile, which may make it less suitable for its intended use. As the paper clip was bent it got harder, but less ductile, until it eventually broke.  The directional properties of the material may also be adversely affected.

The best tools at your disposal to avoid strain hardening are using proper feeds and speeds, tool coatings, and coolant. But we can add a number of other tips and techniques:

I will use the terms “strain hardening” and “work hardening” interchangeably throughout this article.  Let’s talk about this hardening more deeply.

CVD (Chemical Vapor Deposition) and PVD (Physical Vapor Deposition) are coating processes that are often used for the surface treatment of tools and molds.

The strain we apply up to the crossover (where the line changes from blue to green) is the yield stress.  As long as we don’t apply more stress than that, we’re causing elastic deformation and the part will spring back to its original shape when we remove that stress.  If we go past that point, plastic deformation occurs, and if we keep going, the part will eventually fracture or break.  Stress past that point is called plastic stress.

If we look at types of strain, we see two deformation mechanisms.  In tensile deformation, the length of the object increases.  In compressive deformation, the length decreases.