Millingspeeds and feedschart pdf

303 is a free-machining stainless alloy providing the best machinability among the austenitic stainless alloys. It is primarily used on Swiss-type Machines (Screw Machines) when productivity is a crucial factor. The machinability rating is approximately 75%.The sulfur addition, which is accountable for the enhanced machinability in 303 stainless, decreases its corrosion resistance and toughness to below that of 304 and 316 alloys.It has 1.5% carbon (compared to around 0.08% in 304/316); thus, it is less soft, therefore less likely to develop 'build-up edge' , and is more manageable with chip control.Summery:For general Turning of Stainless Steel 303 at stable conditions use a grade with a Semi Hard substrate and CVD coating.In case you are running at a cutting speed that is lower than 390 SFM (120 m/min), it is better to use a grade with aSemi Hard substrate and PVD coating.For general Milling use a grade with a Semi Hard substrate and PVD coating.For detailed carbide grades recommendations, check the Below Chart, or use the Grades Wizrad.Recommended Cutting speed range for turning at stable conditions is 890 - 1180 [SFM] / 270 - 360 [m/min].Recommended Cutting speed range for milling with stable clamping and short overhang is 560 - 750 [SFM] / 170 - 230 [m/min]For detailed cutting speed recomendations, check the Below Table, or use our Speed and Feed Calculator.Equivalent International Designations for Stainless Steel 303StandardNamesae303wnr1.4305dinX8CrNiS18-9bs303S21, 58Mss2346anforZ10CNF18.09uniX10CrNiS 18.09unfF.3508js1SUS303Chemical Composition for Stainless Steel 303ElementAmountChromium (Cr)19.5%Nickel (Ni)10.5%Silicon (Si)2.00%Manganese (Mn)1.50%Molybdenum (Mo)0.60%Sulfur (S)0.30%Carbon (C)0.16%Phosphorus (P)0.04%Cutting Speeds Recomendations for Stainless Steel 303* Click on the speeds below for higher precision in specific conditions!ApplicationVc (m/min)Vc (SFM)Turning270-360890-1180Milling170-230560-750Parting105-145340-480Grooving160-215520-710Drilling75-105250-340Important! The speed estimation is given for an ideal situation:Most suitable carbide gradeStable tool clampingStable workpiece clampingGood quality raw materialA short overhang of the cutting tool.Nominal hardness of the material.etc.Click on the speeds in the above table to get better precision for specific parametersOr use our Speed and Feed CalculatorRecommended Carbide Grades for Stainless Steel 303TurningMilling (Indexable)Parting OffGrooving* If you do nott understand the below table? Read This Explanation to make the most out of it!Grade for TurningFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC2015MM - Stainless SteelTTurningCVDM05 - M15MMMSandvikGC2220MM - Stainless SteelTTurningCVDM10 - M25MMMMSandvikGC2025MM - Stainless SteelTTurningCVDM15 - M35MMMMMSandvikGC2035MM - Stainless SteelTTurningPVDM20 - M45MMMMMMIscarIC807 (IC907)MM - Stainless SteelTTurningPVDM05 - M20MMMMIscarIC6015MM - Stainless SteelTTurningCVDM05 - M15MMMIscarIC6025MM - Stainless SteelTTurningCVDM15 - M35MMMMMIscarIC830 (IC328)MM - Stainless SteelTTurningPVDM20 - M45MMMMMMKennametalKCU10B (KCU10)MM - Stainless SteelTTurningPVDM05 - M20MMMMKennametalKCM15B (KCM15)MM - Stainless SteelTTurningCVDM10 - M20MMMKennametalKCM25B (KCM25)MM - Stainless SteelTTurningCVDM15 - M35MMMMMKennametalKCU25 (KC5025)MM - Stainless SteelTTurningPVDM15 - M30MMMMKennametalKCM35B (KCM35)MM - Stainless SteelTTurningCVDM30 - M40MMMWalterWSM10S (WSM10)MM - Stainless SteelTTurningPVDM05 - M20MMMMWalterWMP20SMM - Stainless SteelTTurningCVDM10 - M30MMMMMWalterWSM20S (WSM20)MM - Stainless SteelTTurningPVDM10 - M30MMMMMWalterWSM30S (WSM30)MM - Stainless SteelTTurningPVDM25 - M40MMMMSecoTM2000MM - Stainless SteelTTurningCVDM05 - M25MMMMMSecoCP500MM - Stainless SteelTTurningPVDM15 - M40MMMMMMSecoCP600MM - Stainless SteelTTurningPVDM20 - M45MMMMMMSecoTM4000MM - Stainless SteelTTurningCVDM25 - M40MMMMTungaloyT6120MM - Stainless SteelTTurningCVDM10 - M20MMMTungaloyT6130MM - Stainless SteelTTurningCVDM15 - M30MMMMTungaloyAH630MM - Stainless SteelTTurningPVDM15 - M30MMMMTungaloyAH645MM - Stainless SteelTTurningPVDM30 - M40MMMMitsubishiMC7015MM - Stainless SteelTTurningCVDM05 - M20MMMMMitsubishiVP15TFMM - Stainless SteelTTurningPVDM10 - M30MMMMMMitsubishiMC7025MM - Stainless SteelTTurningCVDM15 - M35MMMMMMitsubishiMP7035MM - Stainless SteelTTurningPVDM30 - M45MMMMSumitomoAC6020M (AC610M)MM - Stainless SteelTTurningCVDM05 - M25MMMMMSumitomoAC6030M (AC630M)MM - Stainless SteelTTurningCVDM10 - M35MMMMMMSumitomoAC1030UMM - Stainless SteelTTurningPVDM20 - M40MMMMMSumitomoAC6040MMM - Stainless SteelTTurningPVDM25 - M45MMMMMGrade for Milling (Indexable)Filter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikS30TMM - Stainless SteelMMillingPVDM05 - M15MMMSandvikGC1040MM - Stainless SteelMMillingPVDM10 - M30MMMMMSandvikGC2040MM - Stainless SteelMMillingCVDM25 - M40MMMMIscarIC808 (IC908)MM - Stainless SteelMMillingPVDM05 - M15MMMIscarIC830 (IC328)MM - Stainless SteelMMillingPVDM10 - M30MMMMMIscarIC330 (IC328)MM - Stainless SteelMMillingPVDM15 - M40MMMMMMKennametalKC522MMM - Stainless SteelMMillingPVDM10 - M25MMMMKennametalKCSM40MM - Stainless SteelMMillingPVDM20 - M35MMMMKennametalKC725MMM - Stainless SteelMMillingPVDM30 - M40MMMWalterWSM35SMM - Stainless SteelMMillingPVDM25 - M45MMMMMWalterWSP45S (WSP45S)MM - Stainless SteelMMillingPVDM35 - M45MMMSecoMP2501MM - Stainless SteelMMillingCVDM05 - M20MMMMSecoF40MMM - Stainless SteelMMillingPVDM10 - M40MMMMMMMSecoT350MMM - Stainless SteelMMillingCVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelMMillingPVDM15 - M30MMMMTungaloyAH120MM - Stainless SteelMMillingPVDM15 - M25MMMTungaloyT3225MM - Stainless SteelMMillingCVDM20 - M35MMMMTungaloyAH3225MM - Stainless SteelMMillingPVDM20 - M35MMMMTungaloyAH130MM - Stainless SteelMMillingPVDM25 - M40MMMMTungaloyAH3135MM - Stainless SteelMMillingPVDM30 - M40MMMTungaloyAH140MM - Stainless SteelMMillingPVDM30 - M45MMMMMitsubishiMP7130MM - Stainless SteelMMillingPVDM05 - M35MMMMMMMMitsubishiMP7140MM - Stainless SteelMMillingPVDM30 - M45MMMMSumitomoXCU2500MM - Stainless SteelMMillingCVDM05 - M20MMMMSumitomoACM100MM - Stainless SteelMMillingPVDM05 - M15MMMSumitomoACU2500MM - Stainless SteelMMillingPVDM10 - M30MMMMMSumitomoACM200MM - Stainless SteelMMillingCVDM10 - M25MMMMSumitomoACM300MM - Stainless SteelMMillingPVDM20 - M40MMMMMGrade for Parting OffFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC1125MM - Stainless SteelPPartingPVDM10 - M30MMMMMSandvikGC1135MM - Stainless SteelPPartingPVDM20 - M40MMMMMIscarIC807 (IC907)MM - Stainless SteelPPartingPVDM05 - M10MMIscarIC808 (IC908)MM - Stainless SteelPPartingPVDM10 - M30MMMMMIscarIC5400MM - Stainless SteelPPartingCVDM10 - M25MMMMIscarIC830 (IC328)MM - Stainless SteelPPartingPVDM20 - M40MMMMMKennametalKCU10MM - Stainless SteelPPartingPVDM05 - M15MMMKennametalKCU25MM - Stainless SteelPPartingPVDM15 - M30MMMMWalterWSM13SMM - Stainless SteelPPartingPVDM05 - M20MMMMWalterWSM23SMM - Stainless SteelPPartingPVDM10 - M30MMMMMWalterWSM33S (WSM33)MM - Stainless SteelPPartingPVDM20 - M40MMMMMWalterWSM43SMM - Stainless SteelPPartingPVDM30 - M45MMMMSecoCP500MM - Stainless SteelPPartingPVDM10 - M40MMMMMMMSecoCP600MM - Stainless SteelPPartingPVDM20 - M45MMMMMMSecoT350MMM - Stainless SteelPPartingCVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelPPartingPVDM15 - M30MMMMTungaloyAH7025MM - Stainless SteelPPartingPVDM20 - M30MMMTungaloyGH130MM - Stainless SteelPPartingPVDM25 - M40MMMMMitsubishiVP10RTMM - Stainless SteelPPartingPVDM05 - M10MMMitsubishiVP20RTMM - Stainless SteelPPartingPVDM10 - M30MMMMMMitsubishiVP30RTMM - Stainless SteelPPartingPVDM20 - M40MMMMMSumitomoAC1030U (AC530U)MM - Stainless SteelPPartingPVDM10 - M25MMMMSumitomoAC520UMM - Stainless SteelPPartingPVDM15 - M30MMMMSumitomoAC830PMM - Stainless SteelPPartingCVDM20 - M40MMMMMGrade for GroovingFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC1125MM - Stainless SteelGGroovingPVDM05 - M35MMMMMMMIscarIC807 (IC907)MM - Stainless SteelGGroovingPVDM05 - M15MMMIscarIC808 (IC908)MM - Stainless SteelGGroovingPVDM10 - M25MMMMIscarIC830 (IC328)MM - Stainless SteelGGroovingPVDM20 - M40MMMMMKennametalKCU10MM - Stainless SteelGGroovingPVDM05 - M15MMMKennametalKCU25MM - Stainless SteelGGroovingPVDM10 - M25MMMMWalterWSM13SMM - Stainless SteelGGroovingPVDM05 - M20MMMMWalterWSM23SMM - Stainless SteelGGroovingPVDM10 - M30MMMMMWalterWSM33S (WSM33)MM - Stainless SteelGGroovingPVDM20 - M40MMMMMWalterWSM43SMM - Stainless SteelGGroovingPVDM30 - M45MMMMSecoCP500MM - Stainless SteelGGroovingPVDM10 - M25MMMMSecoCP600MM - Stainless SteelGGroovingPVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelGGroovingPVDM15 - M30MMMMTungaloyAH7025MM - Stainless SteelGGroovingPVDM20 - M30MMMTungaloyGH130MM - Stainless SteelGGroovingPVDM25 - M40MMMMMitsubishiVP10RTMM - Stainless SteelGGroovingPVDM05 - M15MMMMitsubishiVP20RTMM - Stainless SteelGGroovingPVDM10 - M25MMMMMitsubishiVP30RTMM - Stainless SteelGGroovingPVDM20 - M40MMMMMSumitomoAC1030U (AC530U)MM - Stainless SteelGGroovingPVDM10 - M25MMMMSumitomoAC520UMM - Stainless SteelGGroovingPVDM15 - M30MMMMSumitomoAC830PMM - Stainless SteelGGroovingCVDM20 - M40MMMMMRecommended Insert Cutting Edge Geometry for Stainless Steel 303Honing Size:0.03-0.05 mm / 0.001-0.002"Rake Angle:9° -11°Land Angle:PositiveLand Width:0.20-0.30 mm / 0.008-0.012"Learn more about carbide inserts Cutting-Edge Geometry Parameters.Our Top Picks

Speeds and feedsformula

Jun 20, 2023 — Standard high speed steel bits are good. 316 and 304 stainless are not hard, they are tough and work harden rapidly . Cobalt is a common alloy ...

M10 X 1.25 : Basic Thread Dimensions (Pitch, minor & major diameters, depth, lead), Tolerance range for all applicable classes and much more.

Stainless SteelSFM chart

The sulfur addition, which is accountable for the enhanced machinability in 303 stainless, decreases its corrosion resistance and toughness to below that of 304 and 316 alloys.It has 1.5% carbon (compared to around 0.08% in 304/316); thus, it is less soft, therefore less likely to develop 'build-up edge' , and is more manageable with chip control.Summery:For general Turning of Stainless Steel 303 at stable conditions use a grade with a Semi Hard substrate and CVD coating.In case you are running at a cutting speed that is lower than 390 SFM (120 m/min), it is better to use a grade with aSemi Hard substrate and PVD coating.For general Milling use a grade with a Semi Hard substrate and PVD coating.For detailed carbide grades recommendations, check the Below Chart, or use the Grades Wizrad.Recommended Cutting speed range for turning at stable conditions is 890 - 1180 [SFM] / 270 - 360 [m/min].Recommended Cutting speed range for milling with stable clamping and short overhang is 560 - 750 [SFM] / 170 - 230 [m/min]For detailed cutting speed recomendations, check the Below Table, or use our Speed and Feed Calculator.Equivalent International Designations for Stainless Steel 303StandardNamesae303wnr1.4305dinX8CrNiS18-9bs303S21, 58Mss2346anforZ10CNF18.09uniX10CrNiS 18.09unfF.3508js1SUS303Chemical Composition for Stainless Steel 303ElementAmountChromium (Cr)19.5%Nickel (Ni)10.5%Silicon (Si)2.00%Manganese (Mn)1.50%Molybdenum (Mo)0.60%Sulfur (S)0.30%Carbon (C)0.16%Phosphorus (P)0.04%Cutting Speeds Recomendations for Stainless Steel 303* Click on the speeds below for higher precision in specific conditions!ApplicationVc (m/min)Vc (SFM)Turning270-360890-1180Milling170-230560-750Parting105-145340-480Grooving160-215520-710Drilling75-105250-340Important! The speed estimation is given for an ideal situation:Most suitable carbide gradeStable tool clampingStable workpiece clampingGood quality raw materialA short overhang of the cutting tool.Nominal hardness of the material.etc.Click on the speeds in the above table to get better precision for specific parametersOr use our Speed and Feed CalculatorRecommended Carbide Grades for Stainless Steel 303TurningMilling (Indexable)Parting OffGrooving* If you do nott understand the below table? Read This Explanation to make the most out of it!Grade for TurningFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC2015MM - Stainless SteelTTurningCVDM05 - M15MMMSandvikGC2220MM - Stainless SteelTTurningCVDM10 - M25MMMMSandvikGC2025MM - Stainless SteelTTurningCVDM15 - M35MMMMMSandvikGC2035MM - Stainless SteelTTurningPVDM20 - M45MMMMMMIscarIC807 (IC907)MM - Stainless SteelTTurningPVDM05 - M20MMMMIscarIC6015MM - Stainless SteelTTurningCVDM05 - M15MMMIscarIC6025MM - Stainless SteelTTurningCVDM15 - M35MMMMMIscarIC830 (IC328)MM - Stainless SteelTTurningPVDM20 - M45MMMMMMKennametalKCU10B (KCU10)MM - Stainless SteelTTurningPVDM05 - M20MMMMKennametalKCM15B (KCM15)MM - Stainless SteelTTurningCVDM10 - M20MMMKennametalKCM25B (KCM25)MM - Stainless SteelTTurningCVDM15 - M35MMMMMKennametalKCU25 (KC5025)MM - Stainless SteelTTurningPVDM15 - M30MMMMKennametalKCM35B (KCM35)MM - Stainless SteelTTurningCVDM30 - M40MMMWalterWSM10S (WSM10)MM - Stainless SteelTTurningPVDM05 - M20MMMMWalterWMP20SMM - Stainless SteelTTurningCVDM10 - M30MMMMMWalterWSM20S (WSM20)MM - Stainless SteelTTurningPVDM10 - M30MMMMMWalterWSM30S (WSM30)MM - Stainless SteelTTurningPVDM25 - M40MMMMSecoTM2000MM - Stainless SteelTTurningCVDM05 - M25MMMMMSecoCP500MM - Stainless SteelTTurningPVDM15 - M40MMMMMMSecoCP600MM - Stainless SteelTTurningPVDM20 - M45MMMMMMSecoTM4000MM - Stainless SteelTTurningCVDM25 - M40MMMMTungaloyT6120MM - Stainless SteelTTurningCVDM10 - M20MMMTungaloyT6130MM - Stainless SteelTTurningCVDM15 - M30MMMMTungaloyAH630MM - Stainless SteelTTurningPVDM15 - M30MMMMTungaloyAH645MM - Stainless SteelTTurningPVDM30 - M40MMMMitsubishiMC7015MM - Stainless SteelTTurningCVDM05 - M20MMMMMitsubishiVP15TFMM - Stainless SteelTTurningPVDM10 - M30MMMMMMitsubishiMC7025MM - Stainless SteelTTurningCVDM15 - M35MMMMMMitsubishiMP7035MM - Stainless SteelTTurningPVDM30 - M45MMMMSumitomoAC6020M (AC610M)MM - Stainless SteelTTurningCVDM05 - M25MMMMMSumitomoAC6030M (AC630M)MM - Stainless SteelTTurningCVDM10 - M35MMMMMMSumitomoAC1030UMM - Stainless SteelTTurningPVDM20 - M40MMMMMSumitomoAC6040MMM - Stainless SteelTTurningPVDM25 - M45MMMMMGrade for Milling (Indexable)Filter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikS30TMM - Stainless SteelMMillingPVDM05 - M15MMMSandvikGC1040MM - Stainless SteelMMillingPVDM10 - M30MMMMMSandvikGC2040MM - Stainless SteelMMillingCVDM25 - M40MMMMIscarIC808 (IC908)MM - Stainless SteelMMillingPVDM05 - M15MMMIscarIC830 (IC328)MM - Stainless SteelMMillingPVDM10 - M30MMMMMIscarIC330 (IC328)MM - Stainless SteelMMillingPVDM15 - M40MMMMMMKennametalKC522MMM - Stainless SteelMMillingPVDM10 - M25MMMMKennametalKCSM40MM - Stainless SteelMMillingPVDM20 - M35MMMMKennametalKC725MMM - Stainless SteelMMillingPVDM30 - M40MMMWalterWSM35SMM - Stainless SteelMMillingPVDM25 - M45MMMMMWalterWSP45S (WSP45S)MM - Stainless SteelMMillingPVDM35 - M45MMMSecoMP2501MM - Stainless SteelMMillingCVDM05 - M20MMMMSecoF40MMM - Stainless SteelMMillingPVDM10 - M40MMMMMMMSecoT350MMM - Stainless SteelMMillingCVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelMMillingPVDM15 - M30MMMMTungaloyAH120MM - Stainless SteelMMillingPVDM15 - M25MMMTungaloyT3225MM - Stainless SteelMMillingCVDM20 - M35MMMMTungaloyAH3225MM - Stainless SteelMMillingPVDM20 - M35MMMMTungaloyAH130MM - Stainless SteelMMillingPVDM25 - M40MMMMTungaloyAH3135MM - Stainless SteelMMillingPVDM30 - M40MMMTungaloyAH140MM - Stainless SteelMMillingPVDM30 - M45MMMMMitsubishiMP7130MM - Stainless SteelMMillingPVDM05 - M35MMMMMMMMitsubishiMP7140MM - Stainless SteelMMillingPVDM30 - M45MMMMSumitomoXCU2500MM - Stainless SteelMMillingCVDM05 - M20MMMMSumitomoACM100MM - Stainless SteelMMillingPVDM05 - M15MMMSumitomoACU2500MM - Stainless SteelMMillingPVDM10 - M30MMMMMSumitomoACM200MM - Stainless SteelMMillingCVDM10 - M25MMMMSumitomoACM300MM - Stainless SteelMMillingPVDM20 - M40MMMMMGrade for Parting OffFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC1125MM - Stainless SteelPPartingPVDM10 - M30MMMMMSandvikGC1135MM - Stainless SteelPPartingPVDM20 - M40MMMMMIscarIC807 (IC907)MM - Stainless SteelPPartingPVDM05 - M10MMIscarIC808 (IC908)MM - Stainless SteelPPartingPVDM10 - M30MMMMMIscarIC5400MM - Stainless SteelPPartingCVDM10 - M25MMMMIscarIC830 (IC328)MM - Stainless SteelPPartingPVDM20 - M40MMMMMKennametalKCU10MM - Stainless SteelPPartingPVDM05 - M15MMMKennametalKCU25MM - Stainless SteelPPartingPVDM15 - M30MMMMWalterWSM13SMM - Stainless SteelPPartingPVDM05 - M20MMMMWalterWSM23SMM - Stainless SteelPPartingPVDM10 - M30MMMMMWalterWSM33S (WSM33)MM - Stainless SteelPPartingPVDM20 - M40MMMMMWalterWSM43SMM - Stainless SteelPPartingPVDM30 - M45MMMMSecoCP500MM - Stainless SteelPPartingPVDM10 - M40MMMMMMMSecoCP600MM - Stainless SteelPPartingPVDM20 - M45MMMMMMSecoT350MMM - Stainless SteelPPartingCVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelPPartingPVDM15 - M30MMMMTungaloyAH7025MM - Stainless SteelPPartingPVDM20 - M30MMMTungaloyGH130MM - Stainless SteelPPartingPVDM25 - M40MMMMMitsubishiVP10RTMM - Stainless SteelPPartingPVDM05 - M10MMMitsubishiVP20RTMM - Stainless SteelPPartingPVDM10 - M30MMMMMMitsubishiVP30RTMM - Stainless SteelPPartingPVDM20 - M40MMMMMSumitomoAC1030U (AC530U)MM - Stainless SteelPPartingPVDM10 - M25MMMMSumitomoAC520UMM - Stainless SteelPPartingPVDM15 - M30MMMMSumitomoAC830PMM - Stainless SteelPPartingCVDM20 - M40MMMMMGrade for GroovingFilter Brand:BrandGradeISOMaterialappAppCoatingApps Range051015202530354045SandvikGC1125MM - Stainless SteelGGroovingPVDM05 - M35MMMMMMMIscarIC807 (IC907)MM - Stainless SteelGGroovingPVDM05 - M15MMMIscarIC808 (IC908)MM - Stainless SteelGGroovingPVDM10 - M25MMMMIscarIC830 (IC328)MM - Stainless SteelGGroovingPVDM20 - M40MMMMMKennametalKCU10MM - Stainless SteelGGroovingPVDM05 - M15MMMKennametalKCU25MM - Stainless SteelGGroovingPVDM10 - M25MMMMWalterWSM13SMM - Stainless SteelGGroovingPVDM05 - M20MMMMWalterWSM23SMM - Stainless SteelGGroovingPVDM10 - M30MMMMMWalterWSM33S (WSM33)MM - Stainless SteelGGroovingPVDM20 - M40MMMMMWalterWSM43SMM - Stainless SteelGGroovingPVDM30 - M45MMMMSecoCP500MM - Stainless SteelGGroovingPVDM10 - M25MMMMSecoCP600MM - Stainless SteelGGroovingPVDM20 - M40MMMMMTungaloyAH725MM - Stainless SteelGGroovingPVDM15 - M30MMMMTungaloyAH7025MM - Stainless SteelGGroovingPVDM20 - M30MMMTungaloyGH130MM - Stainless SteelGGroovingPVDM25 - M40MMMMMitsubishiVP10RTMM - Stainless SteelGGroovingPVDM05 - M15MMMMitsubishiVP20RTMM - Stainless SteelGGroovingPVDM10 - M25MMMMMitsubishiVP30RTMM - Stainless SteelGGroovingPVDM20 - M40MMMMMSumitomoAC1030U (AC530U)MM - Stainless SteelGGroovingPVDM10 - M25MMMMSumitomoAC520UMM - Stainless SteelGGroovingPVDM15 - M30MMMMSumitomoAC830PMM - Stainless SteelGGroovingCVDM20 - M40MMMMMRecommended Insert Cutting Edge Geometry for Stainless Steel 303Honing Size:0.03-0.05 mm / 0.001-0.002"Rake Angle:9° -11°Land Angle:PositiveLand Width:0.20-0.30 mm / 0.008-0.012"Learn more about carbide inserts Cutting-Edge Geometry Parameters.Our Top Picks

Lathe cutting speed chart PDF

Do you want to reach technical audience in the Machining Industry? Look no further! We have a massive audience of professionals, and our precise targeting ensures your message gets across exactly where it needs to be. Learn More

A straight router bit contains edges that are flat and used for making straight cuts, such as for a plunge cut. A straight router bit can even be used for ...

Aluminum milling speed chart

PREMIUM MEMBERSHIP- Ads Free Browsing- Advanced Calculator Options- Quick Access Favorites BarFor Just 2$ / MonthLearn More

Generic Surface Speed Reference ; Wax, 200 ft/min, Use this for prototyping a complex machining process or to make moulds for casting. ; HDPE, 450 ft/min, Softer ...

At Machining Doctor, our mission is to serve the machining industry as a comprehensive and reliable source of technical information. We strive to be the go-to destination for professionals in the niche seeking information, knowledge, and expertise. Join us and stay ahead of the curve! Learn more

This software is integrated in SolidCAM enabling the automation of the design-to-manufacture processes. The main principle of the DriveWorks functionality ...

PREMIUM MEMBERSHIP- Ads Free Browsing- Advanced Calculator Options- Quick Access Favorites BarFor Just 2$ / MonthLearn More

Lathefeeds and speedsChart

Texas A&M University-Corpus Christi Management Student · I am a very hard working individual. I take pride in my work as being the best I can possibly be at ...

We cannot complete your request due to a technical difficulty. You may return to the previous page or go to the homepage and explore other options. For immediate assistance please call us.

Millingspeeds and feedsChart

The rules and principles of cutting speeds and RPM calculations apply to all of the operations being performed on drilling machines.

Oct 30, 2021 — ... cutting tool suppliers use different names and classification methods for their grade charts. This can make grade comparison difficult for ...

Kennametal's tools for threading & inserts are made with tungsten carbide materials and offer precision and consistency for your threading application.

Harvey is an IRS and State Tax Problem Resolution Expert and has established a reputation as a nationally recognized Tax Wizard for hire. Using his exceptional ...