Parr, Larry. How To Harden Steel With Motor Oil last modified March 24, 2022. https://www.sciencing.com/how-4579248-harden-steel-motor-oil/

This site displays a prototype of a “Web 2.0” version of the daily Federal Register. It is not an official legal edition of the Federal Register, and does not replace the official print version or the official electronic version on GPO’s govinfo.gov.

Enter a search term or FR citation e.g. 88 FR 382 30 FR 7878 2024-13208 USDA 09/05/24 RULE 0503-AA39 SORN

The OFR/GPO partnership is committed to presenting accurate and reliable regulatory information on FederalRegister.gov with the objective of establishing the XML-based Federal Register as an ACFR-sanctioned publication in the future. While every effort has been made to ensure that the material on FederalRegister.gov is accurately displayed, consistent with the official SGML-based PDF version on govinfo.gov, those relying on it for legal research should verify their results against an official edition of the Federal Register. Until the ACFR grants it official status, the XML rendition of the daily Federal Register on FederalRegister.gov does not provide legal notice to the public or judicial notice to the courts.

Parr, Larry. (2008, October 30). How To Harden Steel With Motor Oil. sciencing.com. Retrieved from https://www.sciencing.com/how-4579248-harden-steel-motor-oil/

Parr, Larry. "How To Harden Steel With Motor Oil" sciencing.com, https://www.sciencing.com/how-4579248-harden-steel-motor-oil/. 30 October 2008.

Pick up the blue-hot steel with your tongs and immediately immerse it in a vat of room-temperature water. Allow the steel to cool in the water. Your steel is now case-hardened. The outside layer of steel will be at least 40 percent harder than when you started, and your steel will be malleable, rather than brittle like glass.

Hardening steel with motor oil is a way of performing what is called the case hardening of steel. Pure steel is actually too soft for many applications. In order to put a hard layer on the steel, carbon must be fused at the molecular level into the top centimeter or so of the steel. One way to do this is to make the steel red-hot, then plunge it into motor oil. The carbon in the motor oil bonds with the top layer of red-hot steel molecules and forms a tough outer covering on the steel. One last step is necessary, however, before your hardened steel is ready to work with.

The 1936-1994 official print volumes of the Federal Register have been digitalized and are available online in PDF format. We found the following published on May 27, 1977.

Choosing an item from full text search results will bring you to those results. Pressing enter in the search box will also bring you to search results. Choosing an item from suggestions will bring you directly to the content.

If you wish to harden your steel to a deeper level, you can reheat it to red-hot after the first oil bath and give it a second oil bath. After the second oil bath, continue from Step 3.

The documents posted on this site are XML renditions of published Federal Register documents. Each document posted on the site includes a link to the corresponding official PDF file on govinfo.gov. This prototype edition of the daily Federal Register on FederalRegister.gov will remain an unofficial informational resource until the Administrative Committee of the Federal Register (ACFR) issues a regulation granting it official legal status. For complete information about, and access to, our official publications and services, go to About the Federal Register on NARA's archives.gov.

Remove the steel from the oil and wash the item using dish soap and water. Be careful not to drop or strike your steel, as it will be brittle at this stage (much like glass), and could shatter.

Pick up the red-hot steel with your tongs and immediately immerse it into the motor oil. Allow the steel to remain in the oil for approximately 30 to 60 seconds.

Have a fire extinguisher ready in case the oil catches fire when the red-hot steel is introduced. If the oil should catch fire, simply drop the steel item into the vat and use a fire extinguisher or place a lid over the vat to smother the fire.

Heat the steel using a torch or a furnace with bellows. Continue until the steel glows red-hot. Work in a well-ventilated area and wear protective clothing, heavy gloves and eye protection.