Dent Fix Equipment DTFDF-1480 8.0mm HSCO Spot Weld Drill Bit at Great Prices | National Tool Warehouse.

For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

At PDG, our team thrives on the creativity we bring to our clients’ projects and the impact our work has on their organization’s and employees’ success. Here are the other great things we offer to all employees.

Performancecontractors hiring office

Diversity is about your unique perspective. It’s about you, your colleagues, and the world we care for—all backgrounds, beliefs, and the entire range of human experience—coming together. You view the world from a unique vantage point, a perspective that gives you problem-solving potential ideas, solutions & strategies that, when mobilized, can bring health to millions.Inclusion at Performance Development Group is about creating a deep sense of belonging. It’s about a culture where you are valued, your ideas are heard, and you advance this culture for everyone.

Performancecontractors jobs Baton Rouge

Wodenco is the premier manufacturer and supplier of ACME thread inserts you can trust. Integrating Research and development, production, marketing, and general ...

Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000.

1. An orderly pile, especially one arranged in layers: a stack of newspapers. See Synonyms at heap. 2. A large, usually conical pile of straw or fodder ...

We understand the urgency and anticipation that comes with submitting an application. That’s why we typically respond to applications within 48 hours from submission. To ensure impartiality throughout our evaluation process, we use standard questioning techniques. This consistency not only preserves the integrity of our hiring practices, but also guarantees each potential candidate is given the same opportunities to showcase their abilities.

The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

PerformanceContractors jobs salary

For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Map Contents. Basemap Gallery. Print. The layer, FEMA Water Lines, FEMA Flood Hazard Zones, FEMA FIRM Panels, Texas Counties, Lot Lines, cannot be added to the ...

MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

We aim to provide every candidate a positive, engaging, and honest experience. Each job description includes the hiring process so that you know what to expect at each step.

PerformanceContractors projects

A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Everybody comes to the table with a different perspective, idea, and solution for solving problems. We ensure that as many different voices as possible have a seat at the table.

Performancecontractors jobs Near me

US 2 Hole Corner Angle Bracket (PT-302) | Model : BIS201 Features: 2 holes.

Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Performancecontractors jobs

Browse Insert Tool Holders in the Western States Hardware catalog including Carbide Insert Toolholders, Imported,Indexable Turning Tool Holders, Dorian Tool ...

We go above and beyond to build deep, meaningful relationships with our clients through dedicated and responsive solutions, successful implementation, and thoughtful strategies and initiatives.

it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

IHL Canada Building Materials, Construction Supplies.

For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

LARGE-FRAME HMCs / BORING MILLS. Haas EC-1600. EC-1600. CNC Horizontal Mill with 64" x 50" x 32" travels. Starting at US$277,995 CNY ONLY. Learn More Build & ...

The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Image

Our core values are more than words—they guide everything we do, including how we interact with our clients, deliver solutions, and treat our business partners. These values are why we are often referred to new clients, and people love working here.

Except for those rare few souls that write N/C programs for the sheer joy of it, the ultimate purpose of owning, programming, or operating an N/C machine tool is to make a buck. The buck is made by performing a service or making a product better and at lower cost than the competetion can do it. One of the major factors in machine tool economics is time. The longer it takes to do something, the more it costs. The length of time it takes to make a piecepart using N/C is a direct function of the feedrate used. The slower the feedrate, the longer it will take to run the piecepart. Other factors, such as making unnecessary cutting passes, are also important, but using the correct feedrate (and spindle speed) is perhaps the most important factor in the economics of N/C. The optimum feedrate is one that maximizes the Material Removal Rate (MRR) without stalling the spindle or breaking the cutter. Determining the Ideal Feedrate The classic method of determining the feedrate is to decide upon a chip load (how thick a chip you wish each tooth to peel off), typically from 0.003 to 0.020 inch. Then calculate what the spindle speed should be. Next, count the number of teeth on the cutter. Then multiply the three together: Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Feedrate (IPM) = chipload (IN) * RPM * teeth The results of that equation, while adequate for most manual machining operations, is often inadequate for high spindle horsepower N/C machines. In addition to being uneconomical, a feedrate that is too slow can hasten cutting tool failure. As each tooth peels off a chip, it also work hardens the workpiece surface. The depth of this workhardened layer can range from a few millionths of an inch to over a thousandth of an inch. If the feedrate is too slow, the cutting edge of each tooth can be cutting through the workhardened layer (dulling the cutting edge) instead of slicing beneath the layer. A feedrate that is too high can stall the spindle or break the cutter--or both. The feedrate that is required to stall the spindle depends upon the following factors: Horsepower of the spindle drive motor, Material Machining Factor (MMF), the machineability of the workpiece material, Material Removal Rate (MRR), the volume (cubic inches) of material being removed per minute. MRR, in turn, is dependent on the depth of cut, diameter of the cutter, and feedrate. Geometry of the cutter, Sharpness of the cutter. The geometry of the cutter is a minor factor and can be ignored. Good machining practice presupposes the cutter is sharp, so that factor can be ignored. Material Removal Rate (MRR) For milling, the material removal rate (MRR) can be calculated as follows: MMR = depth of cut * the width of cut * spindle speed * the feed per tooth (chip load) * the number of teeth * the spindle speed (RPM). For lathe cuts, the MRR is the product of the mean workpiece circumference * the depth of cut * feedrate (in inches per revolution) * the spindle speed. The mean workpiece circumference is the circumference halfway down the depth of the cut. For drilling, the MRR is the product of the area of a circle the diameter of the drill (drill diameter squared * pi/4) * the feedrate in inches per revolution * the spindle speed in RPM. The horsepower required to run the spindle is the product of the Material Removal Rate (MRR) * the Material Machining Factor (MMF). The MMF, a function of the machineability rating of the workpiece material, is shown in Table 3.3. Table 3.3 Material Machining Factors (MMF) Material MMF Aluminum0.12 Brass0.4 Low-carbon steel1.25 High-carbon & low alloy steel1.5 - 1.9 Stainless and tool steels1.8 - 2.2 Superalloys2.5 - 5.0 More Mathematics For example, suppose a 1-inch-diameter end mill was making a 1-inch-deep cut in low-carbon steel with a feedrate of 10 inches per minute (IPM). The MRR is 1 (depth) * 1 (width) * 10 (IPM) = 10. Table 3.3 shows low-carbon steel has an MMF of 1.25. Thus, it would require 10 (MRR) * 1.25 (MMF) = 12.5 HP to drive the spindle. If the spindle was driven with a 5 HP motor, it could stall and perhaps break the cutter. The feedrate (or depth of cut) would have to be reduced to lower the MRR, so a 5 HP or lower load was placed on the spindle. Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Contract Candidates–If you’re brought on as a contractor, you’ll receive a contract that outlines your responsibilities. We keep you updated with upcoming work and engage on a project-by-project basis.

Thread milling is generally faster than tapping because it can complete the entire threading process in a single pass without requiring multiple ...

Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

PerformanceContractors Welding jobs

and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

GARR TOOL Milling Guide for Drill Mills. 316 www.garrtool.com. ®. * Chamfering *. TECHNIC. AL. ISO Material. HRC. SFM (Vc). CHIPLOAD PER TOOTH (Fz). 154M, 154MA.

Image

We complement our project teams with professional consultants who help us to scale effortlessly, optimize creativity, and deliver award-winning projects.

Performancecontractors jobs port sulphur, la

Since: HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved

Full-Time Candidates–If you’re chosen for one of our positions, you’ll receive a verbal offer. We then follow up with a comprehensive offer packet so understand your role, responsibilities, compensation, and benefits.

HP = MRR * MMF and MRR = depth of cut * width of cut * feedrate it follows that: HP = MMF * depth of cut * width of cut * feedrate. Thus, Feedrate = HP --------------------------------------- MMF * depth of cut * width of cut In the previous example, if the spindle motor were 5 HP Feedrate = 5 HP --------------------------------------- 1.25 (MMF) * 1 (depth) * 1 (width) = 4 IPM   Per tooth chip load = feedrate (IPM) --------------------------------------- spindle RPM * cutter teeth Assuming a spindle speed of 400 RPM and a 2-flute cutter, Chip load = 4.0 IPM --------------------------------------- 400 RPM * 2 teeth = 0.005 inch per tooth Suppose in the previous example the workpiece material is changed to aluminum (with an MMF of 0.12). Spindle horsepower is 5. Spindle RPM is 4000. Feedrate = 5 HP --------------------------------------- 0.12 (MMF) * 1 (depth) * 1 (width) = 41.7 IPM   Chip load = 41.7 IPM --------------------------------------- 4000 RPM * 2 teeth = 0.0052 inch per tooth Next:  Review Questions for Chapter 3 Back to Contents Page Updated Jan. 9, 2002 Copyright © 1988-2002 by George Stanton and Bill Hemphill All Rights Reserved