Form turning stainless steel should allow sufficient material to be removed to avoid surface work hardening problems. This applies to both primary and secondary cuts in multi-cut operations. Feed must be maintained as the tool enters the work-piece. For form tool turning deep or complex shapes, slower speeds should be considered. The flow of cutting fluid, (coolant), must be carefully controlled to ensure that a consistent, large flow volume is delivered to the cutting edges at all times during form tool turning of stainless steel.

Too high a speed can result in tool tip burning. Too low a speed can result in chip build-up on the cutting edge. As a general rule, when there are cutting problems adjust the speed first and then, where necessary, the feed second.

Circular tools require an end cutting edge angle relief, usually between 10 and 15 degrees. The angle should be reduced as the depth of cut increases on larger diameter work-pieces to around 5 degrees, to avoid tool deflection. These smaller angles can result in some burr being left which may have to be trimmed off with a second cut. ‘Above centre’ distances should about 3mm.

For over 50 years, Sporty’s Tool Shop has kept American homes and gardens looking their best, featuring home improvement tools, garden and lawn care supplies that not only get the job done, but get the job done right.

What you don’t like is shopping for big clothes. Outfits for the big guy – whether you’re big in height, girth or both – are difficult to find in many men’s clothing stores. The big and tall shops have them, but being a big guy doesn’t necessarily mean you’re a big ‘fashion’ guy, and the sales clerks aren’t always much help beyond pointing you to the fitting room and taking your credit card.

Either blade or circular tools can be used. Circular tools are more rigid and provide a better heat sink capacity than blade cutters and so are generally preferred for parting-off stainless steel, where sufficient cut depth is allowed by the tool geometry. Circular tools are also better for interrupted cuts as the tool passes through details like drilled holes. Back rake angles should be between 6 and 10 degrees.

End and side relief angles must be ground flat, without any concavity. Concave faces reduce the support at the cutting edge and can result in chipping or breaking.

Back rake angles should be between 4 and 10 degrees. The smaller angles suit secondary cuts in multi-cut operations. The larger angles suit single cut operations or the primary cuts of multiple cut operations. Top face and back rake angles should have a smooth polished finish to avoid chip flow problems that can result in poor finish or overheating due to poor access of coolant to the cutting edges. Side relief and clearance angles should be between 1 and 5 degrees. The deeper the cut, the larger the angle. ‘Above centre’ distances should about 3mm.

The surface speeds shown for the different tool types are at the set depths of cut and feed shown. If depth of cut and feed are increased, the speed must be reduced. Alternatively for increased speeds, reduce the depth of cut and feed. For austenitic steels, (e.g. 304, 1.4301), the depth of cut must however always undercut the induced work hardened layer, so increase in speed must be carefully limited. Similarly, it is important to leave enough steel on the surface when completing the last roughing cut to enable sufficient finishing cut depth. Where this is impractical, a carbide tool used at high speed, low feed and a shallow depth of cut is an option.

Traditionally high speed steel (HSS) tools have been used for most turning operations, but carbide tipped tools are now also used. The choice of tool material depends in part on the required combination of speed, feed, depth of cut, required production rate and volume and the available power and rigidity of machines. This article gives suggested feeds and speeds for single point, form tool and cut-off (parting-off) tool geometry turning taken from the BSSA Stainless Steel Specialist Course Training Note No.9 ‘Machining Stainless Steels’.

Maintain the perfect home & garden, with home improvement tools that will have all of your indoor and outdoor living spaces covered.^

Invitations for applications for insurance on Catalogs.com are made through QuoteLab, LLC and transparent.ly. Submission of your information constitutes permission for an agent to contact you with additional information about the cost and coverage details of health and auto insurance plans. Descriptions are for informational purposes only and subject to change. Insurance plans may not be available in all states. For a complete description, please call to determine eligibility and to request a copy of the applicable policy. Catalogs.com is not affiliated with or endorsed by the United States government or the federal Medicare program. By using this site, you acknowledge that you have read and agree to the Terms of Service and Privacy Policy.

Our bedroom is supposed to be our haven, a place of our own where we can retreat, unwind, relax, sleep, and do “other things” if […]

End relief angles should be between 7 and 10 degrees and should be ground flat to provide maximum support for the cutting edge. Side relief angles should be between 2 and 3 degrees. For large cut depths larger the side relief angles may be needed to avoid tool seizure.

BSSA The Innovation Centre 217 Portobello Sheffield S1 4DP T: +44 (0)114 551 8170 Technical: ssas@bssa.org.uk General: kate.vale@bssa.org.uk

Since 1996, Catalogs.com has been considered the web's catalog shopping authority. Our trends experts have carefully reviewed thousands of catalogs and online stores and have featured only the most respected, distinctive, and trusted ones. From popular favorites to new discoveries, you'll shop and save with exclusive coupon codes!