Good end mills for a beginner? : r/Machinists - best carbide end mills
I have given up on buying cheap. With the Mitsubishi inserts, the VP05RT grade is very similar to the Kyocera PR1425 grade and the PR1125 grade. The VP15RT is not as hard a coating.
That little selection now gives me the basics, I think. The tool bits Neil Lickford listed gives me a clue to the grades I'll be after. His second photo, the PR1125, looks remarkably similar to the one that I used in the little Valenite holder I had all those years ago. It didn't have a central clamp screw, it sat on a pin and was locked from the side by a wedge, held in by a screw, if I remember right. It got used for just about everything short of boring holes.
A largish, 20mm shank Sandvic boring bar with triangular inserts came to me, so it seemed silly to refuse, I know I'll end up using it quite a lot and the inserts now seem fairly simple to find.
Starting again, almost – but not quite – from scratch, I find myself bedazzled by the plethora of carbide tipped cutting systems in use today compared with 15 years ago. In those days I had three inserted tools, one for surfacing and two boring bars. I was given them and they were all Valenite. The rest were HSS, with a couple of brazed tip carbide items for the heavy stuff.
I have to confess I have not had poor durability from my ones, but I admit it is the luck of the draw whether you get an insert with the tool that's suitable for the job in hand. This thread: **LINK** showed the dramatic effect of correct & incorrect inserts in use in the same tool. In one case the face mill was unusable, and in the other it worked like a dream. You could be mistaken in putting the whole blame down to a poor tool, when it's just unsuitable inserts.
Home › Forums › Workshop Tools and Tooling › Carbide Insert decode This topic has 11 replies, 9 voices, and was last updated 20 May 2018 at 07:54 by I.M. OUTAHERE. Viewing 12 posts - 1 through 12 (of 12 total) Author Posts 17 May 2018 at 08:22 #18929 Will NobleParticipant @willnoble66529 Advert 17 May 2018 at 08:22 #354304 Will NobleParticipant @willnoble66529 Starting again, almost – but not quite – from scratch, I find myself bedazzled by the plethora of carbide tipped cutting systems in use today compared with 15 years ago. In those days I had three inserted tools, one for surfacing and two boring bars. I was given them and they were all Valenite. The rest were HSS, with a couple of brazed tip carbide items for the heavy stuff. Now there are dozens and dozens, some VERY cheap and probably VERY poor durability. I've looked around for a decode and compatibility chart, can find several that do some aspects but none that provide a reasonably comprehensive chart, or table. What does everyone use as a reference/decode/database, or chart? Will 17 May 2018 at 09:10 #354312 EmgeeParticipant @emgee Hi Will Start learning more at this link **LINK** Emgee 17 May 2018 at 09:55 #354322 Rik ShawParticipant @rikshaw Hello Will – I mostly use this: **LINK** 17 May 2018 at 09:58 #354324 MuzzerParticipant @muzzer The nomenclature is defined in an ISO standard. So you can find explanations from most of the big suppliers and the primary part of the designation tells you a lot of what you need to know. They are cross compatible to a fair degree. However: There are different insert types for turning and for milling. Each manufacturer has its own variations, grades and detail geometries. US suppliers use a variation on the numbering system to account for their imperial measurements. I tend to default to Korloy or Mitsubishi but there are quite a few reputable alternatives, mainly Japanese, Korean or German. The links here point to Korloy. Murray PS – whenever this comes up, Rik pastes the link to Carbide Depot. And I point out that that is a US site with imperial inserts (and part numbers). We live in the rest of the world where the metric system prevails. The part numbering is different. Edited By Muzzer on 17/05/2018 10:01:13 17 May 2018 at 12:24 #354347 JasonBModerator @jasonb I tend to use the one in MSC's virtual catalogue, if you put pages 362 &363 on double page spread its easy to follow Edited By JasonB on 17/05/2018 12:24:28 17 May 2018 at 13:54 #354367 richardandtracyParticipant @richardandtracy Posted by Will Noble on 17/05/2018 08:22:55:
For the DCMT11 holder I use these, they are an AL specific turning insert, but as long as the feedrate is not too high, cut steel very well also. Just awesome with plastics, as they are very sharp.
Thankfully the hotel was about a km. from the touristy part of Colaba, and I got to see the view towards the Gateway instead of the ‘from the Gateway’ view that I would have seen as a regular tourist. I went camera-mad and got these pictures, mostly at dawn.
Having heeded warnings about QC T2 toolholders, I checked those on offer at Doncaster and noted the RDG variety seemed well finished and to fit the QC post very well. I now have four holders to play with. More needed.
Part of the problem is that more choice gives the opportunity to make more bad choices, and it's up to us to learn enough to make good ones instead.
To cut metal profitably, there are in fact only 3 parameters that you really need to understand to select the right insert for your application. These are the numbers marked in red in the above example. The others, like the insert shape and cutting edge length, are automatically decided based on the holder that you are using. In the table below, you have to use your brain only in selecting the parameters where there is a brain in the row.
Keep a look out on ebay sometimes the inserts you want will pop up at a good price and be from a known quality manufacturer .
Looking at the boats tethered to the shallow sea bed, I wondered how come nobody ever stole any of those expensive speedboats. Must be easy to just start one of them and drive (is that even the right word for moving a boat – I wonder what is the right word ?) it off to some neighbouring town, and nobody would ever know. Good thing I can’t swim and barely know the front end of a boat from the back (I only recently learnt that they’re called fore and aft respectively) – might have been tempted to steal one of those posh boats otherwise.
Corner radius – 04: In this case 0.4mm. For hobby machines corner or nose radius of 04 – 0.4mm (for finishing) or 08 – 0.8mm (for general use) are suggested. Finer radius than this, such as 00 – sharp point, 01 – 0.1mm and 02 – 0.2mm should generally be avoided as they are more suited for use at very high speeds on industrial CNC machines with high rigidity. If used on hobby machines, such inserts are more likely to chip easily.
I have a Canela SDNCN2020 facing tool (the only one) that came with the lathe. It takes DCMT inserts and I bought a boring bar and a SDJCR1616 rightward surfacing tool at Doncaster that takes the same type/size for the very reason XD 351 says – to cut down on stock range. It would seem my instincts weren't too far off but what sparked this question was looking at all the options and thinking 'what a minefield, when you don't have the basics'.
When i switched over to insert tooling i made the mistake of buying a toolholder kit without thinking about the types of insert they used , I ended up with a set of holders that used three different inserts and mostly only use two of the holders out of a set of six anyhow .
The name Colaba is a corruption of the original name Kolabhat, meaning a Koli village in the Koli dialect (a variant of Marathi). The Kolis, mostly fisherfolk, were the original inhabitants of the group of 7 islands now known as Mumbai. The name Mumbai itself is derived from Mumbadevi, the patron goddess of the Kolis.
You wouldn't do to badly to look at MEW of the last couple of months where (for lathe tools) Neil went through the nomenclature of ones suitable for use on smaller machines. Failing that, look at the ArcEurotrade range that's up for sale. The Arc ones are probably all Chinese made, and look similar or identical to the ones available on E-bay, and none the worse for it. I am pretty convinced China is passing out of the 'make it – regardless of quality' phase and into the 'trying to increase quality and make durable items' phase. Same as Japan & S Korea did in the past. I think we're at the relatively short point where quality is good enough and price is still low that both Japan and S Korea showed 40 and 20 years ago respectively. Blink & you'll miss it…
There is a standard code for describing inserts, typically four letters followed by a number. The full code is too complex to detail here, so as an example let’s look at a typical insert that suits smaller lathes: CCGT 060204, photo 9:
Shape – C: 80-degree diamond, this give a well-supported tip that can work into a 90-degree corner. Some other useful shapes are S – square as shown in photo 6; R – round; T – equilateral triangle and V – a long-thin diamond shaped tool intended for CNC profile turning but useful for delicate work.
Holder style – L: This is the way the toolholder presents its cutting edge to the work. An ‘L’ toolholder essentially offers the 80-degree insert so it can cut freely into a 90-degree corner. Unlike the knife tool this gives an ideal geometry for both turning and facing with the same tool, which is why this style of toolholder is so popular.
If you purchase left hand , right hand toolholders and a boring bar that all use the same insert you can really economise on the inserts and usually use a worn insert in the opposite hand toolholder to get more use from it .
The nomenclature is defined in an ISO standard. So you can find explanations from most of the big suppliers and the primary part of the designation tells you a lot of what you need to know. They are cross compatible to a fair degree. However:
Wow! Thanks, every body. Lots to digest from the links and posts, alongs with charts to peruse. Muzzer's caveat reference Rik's link to the US site is noted. I've found and read the article suggested by Richard and bookmarked all the links for a bit of reading.
Some time back I stayed in a hotel in Colaba in Mumbai, very close to the Gateway of India, at the southernmost tip of Mumbai.
DTI Glass Willis Farmers Engine in 2″ scale Reliance drill grinding jig instructions I will probably be expunged from the forum for this My very own Quick Change toolpost Buying a quick change tool post – Which one? SC2 mini lathe pops RCD when turned on? Stuart Dynamo What did you do Today 2024 Hot rolled angle problems
It can be a bit bewildering looking at all the types of inserts which have been designed mostly because of the boom in cnc machining and are for taking heavy cuts on powerful machines – which our machines are not !
Height and width of shank – 1010: the shank of the tool is 10mm by 10mm, this suits the SC4 510, 0808 shank (8mm) toolholders work well with mini-lathes.
Hole/Chipbreaker – T: A 40-60-degree double countersunk hole (it has to match the screw used by your toolholder) and a single-sided chipbreaker.
Inserts are sometimes sold without the corner radius being specified. It is worth checking as smaller numbers are suitable for machining fine work and sharp internal corners, while a larger corner radius makes it easier to get a good finish and leaves a distinct fillet in a corner.
Tolerance – G: This is the tolerance of various measurements of the insert. The tolerance letter can be confusing as the tolerance reflects other properties of the insert. The two you are most likely to encounter are G and M. M is a general use moulded insert, while G is ground further into specific shape (e.g. Top rake for additional tolerance for specific application, and so will cost more than the M moulded inserts. Both types are available coated for better wearing properties, or un-coated or polished for the G type. In the hobby environment, M type are generally used for machining of steel, stainless steel and cast iron. The polished G type with ground edges, are ideal for cutting aluminium, brass and other non-ferrous metals.
The only wish list bits I couldn't get at Doncaster were any of the D1-4 things. RDG, amongst others, stock it but hadn't any there. I guess it is, after all, a Model Engineers Exhibition and my stuff is a bit on the large side for that.
Model Engineer and Model Engineers' Workshop are leading magazines for modellers, with reputations for bringing you the best tips, tricks, and inspiration from the model engineering world. From miniature steam locomotives to clocks and tools, get the most out of your hobby with Model Engineer and Model Engineer's Workshop.
I tend to default to Korloy or Mitsubishi but there are quite a few reputable alternatives, mainly Japanese, Korean or German. The links here point to Korloy.
Photograph 10 shows the codes on the SCLC-R1010E06 and SCLC-L 1010E06 toolholders we saw in photo 5. These toolholder codes break down as:
I've looked around for a decode and compatibility chart, can find several that do some aspects but none that provide a reasonably comprehensive chart, or table.
The last surprise was this 8mm( R4) button turning insert. I thought that it will chatter like no tomorrow and give a poor surface finish. But it comes up looking like a mirror. This I used on the bearing holder for the sensitive drill adaptor. Works really well on Al, not yet tried on steels yet.
In the midst of all this, I need to find some butt welded HSS tools. In the past I used a Myford set. A bit diminutive on my old Student, more so on this Master but still very useful. I think a new set is in order.
These are my main inserts for my Myford lathe and what I turn. This little insert is quite amazing. It does outer turn, fits my small boring bars, and will cut everything from Al to bearing races, including Ti. Technically it is a stainless steel grade,CCGT060202MP-CK-PR1425
The shape, hole, cutting edge length and clearance are matched to the toolholder, but it is usually possible to use inserts with different tolerances, corner radiuses and even thicknesses in the same toolholder.
Search for: Home › Forums › Workshop Tools and Tooling › Topics Viewing 25 topics - 1 through 25 (of 25 total) Topic Voices Posts Last Post DTI Glass Started by: Chris Crew in: General Questions 4 4 10 October 2024 at 22:15 peak4 Willis Farmers Engine in 2″ scale Started by: Luker in: Work In Progress and completed items 6 11 10 October 2024 at 22:07 Nigel Graham 2 Reliance drill grinding jig instructions Started by: farmer_joe in: Workshop Tools and Tooling 2 2 10 October 2024 at 21:59 Charles Lamont I will probably be expunged from the forum for this Started by: Ian P in: The Tea Room 2 3 10 October 2024 at 21:52 Ian P My very own Quick Change toolpost 1 2 Started by: Iain Downs in: Workshop Tools and Tooling 16 31 10 October 2024 at 21:45 Charles Lamont Buying a quick change tool post – Which one? Started by: Volans in: Workshop Tools and Tooling 5 10 10 October 2024 at 21:32 Macolm SC2 mini lathe pops RCD when turned on? 1 2 3 Started by: andy198712 in: General Questions 10 53 10 October 2024 at 21:17 Robert Atkinson 2 Stuart Dynamo 1 2 3 Started by: Steve Rowbotham in: Beginners questions 13 70 10 October 2024 at 20:27 Ian P What did you do Today 2024 1 2 … 16 17 Started by: JasonB in: The Tea Room 62 402 10 October 2024 at 20:21 Nicholas Farr Hot rolled angle problems Started by: Mick Bailey in: Materials 8 24 10 October 2024 at 19:24 Nicholas Farr Chester Super Lux advice 1 2 … 5 6 Started by: Taf_Pembs in: Manual machine tools 18 135 10 October 2024 at 18:18 Taf_Pembs JPEG Slide Show Started by: Vic in: The Tea Room 6 7 10 October 2024 at 18:18 Peter Cook 6 Farm Boy 1 2 3 4 Started by: Dalboy in: I/C Engines 14 86 10 October 2024 at 17:56 Dalboy A Huge Thank You from the Melbourne Society of Model and Experimental Engineers! Started by: dhendley in: Model Engineer. 1 1 10 October 2024 at 15:25 dhendley Chinese Mini-Lathes/Mills – DC Motor Controllers Started by: Andre ROUSSEAU in: Help and Assistance! (Offered or Wanted) 6 10 10 October 2024 at 14:47 Robert Atkinson 2 Boxford Replacement bearings Started by: Bernard Reilly in: Help and Assistance! (Offered or Wanted) 1 1 10 October 2024 at 13:37 Bernard Reilly Lathe headstock bearing access Started by: Mike Hurley in: Manual machine tools 8 12 10 October 2024 at 12:40 mgnbuk New guy from Norway, planning a Bonelle grinder 1 2 Started by: Fulmen in: Introduce Yourself – New members start here! 17 38 10 October 2024 at 10:50 John Hinkley Sizing of 1/4” hex shanks Started by: Bill Phinn in: Workshop Tools and Tooling 14 22 10 October 2024 at 06:57 JasonB Thiel Nassovia vertical metal saw Started by: Sonic Escape in: General Questions 8 23 9 October 2024 at 12:18 not done it yet About cheap grinders 1 2 Started by: Sonic Escape in: Workshop Tools and Tooling 18 33 9 October 2024 at 12:03 Tony Pratt 1 Racing Motor Cycle Adhesion 1 2 Started by: Peter Cook 6 in: The Tea Room 18 35 9 October 2024 at 11:27 Hopper Bed for 6040 CNC? 1 2 3 4 Started by: Steve355 in: CNC machines, Home builds, Conversions, ELS, automation, software, etc tools 12 90 9 October 2024 at 10:20 Steve355 Deleted messages Started by: jimmy b in: New Forum Software questions, comments and Test Threads 1 1 9 October 2024 at 08:49 jimmy b Weather Started by: Michael Gilligan in: The Tea Room 1 1 9 October 2024 at 05:11 Michael Gilligan Viewing 25 topics - 1 through 25 (of 25 total)
My other mainstay turning insert is the TNGG160402R-S PR1125 (Wonder Insert) called a Wonder insert by the NZ seller. It really is just that. Like the other little insert, it will cut all materials including bearing races, and Ti. I mainly just get the R0.2mm inserts, as I often need a fairly sharp corner for so many things. The seller I buy from also does sell single inserts as well, so very helpful to the model market. I find that the smaller radius has less tool pressure loading. As long as the feedrate is 25% of the tool radius, it will give a very good surface finish..
Length of holder – E: 70mm, this is rarely critical but shorter holders suit smaller lathes and longer holders can be ‘overhung’ to extend their reach. A is very short (32mm) and Q is 250mm, so if your chosen size is not available a letter up or down will usually work.
PS – whenever this comes up, Rik pastes the link to Carbide Depot. And I point out that that is a US site with imperial inserts (and part numbers). We live in the rest of the world where the metric system prevails. The part numbering is different.
It is also possible to get carbide inserts with a ‘wiper tip’, this is the equivalent of an HSS tool with the tip stoned to have a small flat on it, and gives an excellent surface finish.
Some, but not all, the codes used for inserts are used for toolholders, in particular a simpler scheme is used for the clamping method.