The nature of the steel stud may matter. Do you know what it is? Stainless steel work hardens but can be drilled with ordinary HSS provided the right technique is used. (Basically pressing hard enough to cut, but not overdoing it. Needs practice.)

Model Engineer and Model Engineers' Workshop are leading magazines for modellers, with reputations for bringing you the best tips, tricks, and inspiration from the model engineering world. From miniature steam locomotives to clocks and tools, get the most out of your hobby with Model Engineer and Model Engineer's Workshop.

A far better way is to build up a pillar of weld on the exposed end of the stud using a mig welder, then when the pillar is high enough to then weld a suitable nut on top of the whole lot. The heat of the weld is almost always enough to free off the stud and is a simple twist-out job. Use an aluminium bush to prevent the weld and spatter sticking to the surrounding metal.

Other hardened metals are too hard for HSS, or at least blunt it rapidly. Various choices for these, in rough order of rising hardness and cost. HSS coated with yellow TiN, Cobalt (5 or 8%), Coated Cobalt, Carbide Tipped (TCT), solid Carbide, and exotics like Diamond or Boron Nitride. DIY store drills are best avoided, buy from someone selling to metalworkers.

Diesel 3 1/2 juliet Mini Mill Switch Controller Help Please Allchin Crown Stay Milling Cutter insert radius Warco mill lubrication My mini lathe won’t latch on Lathe vibration in workshop Renishaw touch probe bits Thiel Nassovia vertical metal saw

I found a clip on Youtube on how to drill a stud that had snapped below the surface. Mine is above the surface but it gave me an idea on how to make a guide.

You say a hardened stud, how hard. I would think the stud would be tough not hard, as in En8 or 16. Hardening would make the thread brittle and likely to break. Usually studs can be drilled out and removed with normal HSS drills. I have never come across a hard stud since forces are in tension with no abrasive action requiring hardness.

Solid carbide would be the answer if you could use a drill press, but with a hand held drill you would just break the bit. However, there are Bosch Multiconstruction drills in sets which have carbide tips and steel shanks like masonry drills. It is certainly possible to sharpen the tip of a regular masonry drill, hard going with a standard grinding wheel, but easy with a green wheel, or diamond wheel.

Some sort of drill bush to keep the drill on line would help if it is possible, and maybe using a Dremel to create a start point for the drilling especially if the fractured end is not flat.

Search for: Home › Forums › Manual machine tools › Topics Viewing 25 topics - 1 through 25 (of 25 total) Topic Voices Posts Last Post Diesel 1 2 Started by: Vic in: The Tea Room 20 44 14 October 2024 at 01:44 Paul Kemp 3 1/2 juliet Started by: 474564 in: Help and Assistance! (Offered or Wanted) 6 18 14 October 2024 at 01:28 Paul Kemp Mini Mill Switch Controller Help Please Started by: Blue Heeler in: Manual machine tools 2 3 14 October 2024 at 00:12 Blue Heeler Allchin Crown Stay Started by: Peter Howell 1 in: Traction engines 5 6 14 October 2024 at 00:04 duncan webster 1 Milling Cutter insert radius Started by: Vic in: Workshop Tools and Tooling 2 2 13 October 2024 at 23:58 Nigel Graham 2 Warco mill lubrication Started by: Peter Venn in: Workshop Tools and Tooling 10 16 13 October 2024 at 23:18 Dave Halford My mini lathe won’t latch on Started by: Paul McDonough in: General Questions 4 5 13 October 2024 at 22:47 Huub Lathe vibration in workshop Started by: Mark Salzedo 1 in: General Questions 11 19 13 October 2024 at 21:04 Dave Halford Renishaw touch probe bits Started by: gerry madden in: Electronics in the Workshop 5 14 13 October 2024 at 21:01 Michael Gilligan Thiel Nassovia vertical metal saw 1 2 Started by: Sonic Escape in: General Questions 9 31 13 October 2024 at 20:53 Sonic Escape Hemingway engraving tool Started by: Mike Waldron in: Manual machine tools 4 14 13 October 2024 at 20:08 Mike Waldron Creworks Chinese Mini Lathe – interesting Started by: Lee Cooper in: Manual machine tools 9 19 13 October 2024 at 19:40 not done it yet How long will a 3 Jaw chuck last Started by: Kim Garnett in: General Questions 16 25 13 October 2024 at 18:45 not done it yet Filament Dryers Started by: Colin Heseltine in: 3D Printers and 3D Printing 6 9 13 October 2024 at 17:44 Colin Heseltine My very own Quick Change toolpost 1 2 Started by: Iain Downs in: Workshop Tools and Tooling 16 32 13 October 2024 at 17:01 mark smith 20 Burdett 70 Mk2 Surface Grinder Started by: Me. in: General Questions 4 9 13 October 2024 at 12:12 Me. Zeamons Orrery Started by: Alan Charleston in: Help and Assistance! (Offered or Wanted) 9 18 13 October 2024 at 11:50 ChrisLH brushless DC motor for mini lathe 1 2 Started by: Henry Rancourt in: General Questions 23 49 13 October 2024 at 11:42 Dell Jekyll’s “Pendulous” Engine c 1870 1 2 Started by: JasonB in: Stationary engines 8 27 13 October 2024 at 10:20 JasonB The Incredible Shrinking Hose Started by: Greensands in: The Tea Room 10 10 13 October 2024 at 09:16 larry phelan 1 My Grandson & I steaming the new RAT Steam Engine Started by: Blue Heeler in: Stationary engines 2 3 13 October 2024 at 04:51 Blue Heeler Cleanup and deburring wheels Started by: colinb in: Beginners questions 6 6 12 October 2024 at 22:09 Vic What did you do Today 2024 1 2 … 16 17 Started by: JasonB in: The Tea Room 62 407 12 October 2024 at 21:32 Nicholas Farr New guy from Norway, planning a Bonelle grinder 1 2 Started by: Fulmen in: Introduce Yourself – New members start here! 18 44 12 October 2024 at 20:56 Fulmen alchin 1.5 scale traction engine HELP Started by: joseph tatler in: Traction engines 4 5 12 October 2024 at 20:16 noel shelley   Viewing 25 topics - 1 through 25 (of 25 total)

CEATEC Medizintechnik is a family company in the second generation and was founded in 1995. CEATEC offers a wide range of surgical products from different areas. CEATEC has been certified according to the DIN EN ISO norm and other standards right from the start.

I made three using the process above, the other 2 had a 6 and 7.5 mm hole. The two nuts were then separated and the bolt removed. The joining nut then screwed onto the snapped stud that was on the engine. The drilled bolt with the 4mm hole then screwed into the joining nut. I had a guide.

Welding, drilling (even dissolving in alum might be appropriate on the odd occasion in the right circumstances – I just removed a broken tap from a brass item that way – although this is presumably into steel as even really tough bolts are not usually needed into aluminium).

Whilst getting replies I changed the 4mm guide for the 6mm guide, not sure why. Anyway the 6mm drill bit worked. My cordless drill went flat so had to recharge it. Then progressed to the 7.5mm guide. I was not gentle enough, the bit bit got stuck and sheered the rest of the stud as the walls were now thin.

Home › Forums › Manual machine tools › Help and advice on a drill bit for hardened steel This topic has 10 replies, 8 voices, and was last updated 14 October 2019 at 22:03 by old mart. Viewing 11 posts - 1 through 11 (of 11 total) Author Posts 14 October 2019 at 11:59 #433243 Ian m 1Participant @ianm1 I am confused as to what type of drill bit I need to drill a hardened steel stud that has snapped due to someone's ham fistedness. I think I need cobolt, is this correct 5% or 8%? what tip angel and helix angle do I need? Seeing references to these on the internet has blown my mind. I'd appreciate what good brands to look at. I want to get 4mm, 6mm and 7.5mm drill bits. These will be used in an electric hand drill not a pillar drill or lathe.

I don't have a good track record drilling out hardened studs – broken drills, blunted drills, and scars around the work. No help at all, but the professionals use spark-erosion or weld a temporary new head on the stud to get it out. I expect someone else will offer better advice!

I used a 10mm joining nut on a 10mm bolt, I added a single 10mm nut and locked the joining nut and ordinary nut together. I cut the bolt to the length of the two nuts. placed the lot into the chuck of the lathe holding by the joining nut and pushed back in the chuck so the single nut was clear of the jaws. I then centre drilled and followed this with a 4mm hole all the way along the length of the bolt.

I am confused as to what type of drill bit I need to drill a hardened steel stud that has snapped due to someone's ham fistedness.

Assuming your stud is hardened within ordinary limits, I'd try a TCT drill as offered for drilling stainless steel. If that fails, solid carbide, but they're expensive and brittle. Attempting the job with a hand drill is disadvantageous because they move about and magnify operator mistakes. Getting the cut to start can be tricky because the point tends to skate about. Good idea to centre-pop the stud (if you can) to steady the cutting point and to use split-point drills. Easier to drill the stud if the drill's held firmly in a stand, even a home made one.

Image

Personally I wouldn't attempt to drill a hardened steel stud unless it was with a drill press or mill and with the component clamped in place.

Image

If this is to drill out an exhaust manifold stud or thermostat housing it is probably rusted in and the welding method is best

Image

In the end I think the problem was the 4mm bit not being very good. I apologise if I have wasted your time but when I posted I was desperate and you guys I thought would know.